TeSys U LUTM Controller User Manual 03/2008 - Schneider Electric

More documents

Recommendations

Info

Operation of the LUTM controllerExamples ofApplicationsMachines with manual local control.2-wire control by the controller I/O (non-reversing)1 23 41 Channel 12 Channel 23 Any fault4 Control unitfault2-wire control by the controller I/O (reversing)31 23 41 Channel 12 Channel 23 Any fault4 Control unitfault5 External fault53-wire control by the controller I/O (reversing)31 23 41 Channel 12 Channel 23 Any fault4 Control unitfault5 External fault532 1743233 03/2008
Operation of the LUTM controllerInputs UsedWITH aCommunicationModule7 inputs are used in a configuration with a communication module.Input Function Output CommentI.1 In "local" mode: Each input controls the 13 = state of the inputI.2 output relay.23 = state of the inputI.1 In "remote via the bus" mode: These inputs are 13 = state of the registerI.2available for sending back external data via thecommunication bus (writing to a register).23 = state of the registerNote: If the voltage is too low, the output opens.An external fault or control unit fault has no effect on the state of these relays.I.3 or I.4I.5 RST(Reset)I.6 SF(SystemFault)These inputs are dedicated to feeding backthe state of the contactor controlled by theoutput relay.This input is dedicated.It is used for remote "manual" reset of thecontroller following a control unit fault.This input is dedicated.It is used to feed back trip data from anadditional protection device to the controller.- - -- - -- - -Using a reset button on the front of the rackor control panelExample: Receipt of the data provided by the"Trip" NC contact:=> For a circuit-breaker, a sensor relay, avoltage relay=> For a string of these contactsIn "local" or "remote via the bus" modeThis input is used to send back external data via the communication bus (writing to a register).In "local" mode. Output = state of the inputIn "remote via the bus" mode. Output = state of the registerI.10In "mixed" mode.This input feeds back the "local" or "remote via the bus" data and enables the controller to managethe command priorities.If I.10 = 1 then: "local" mode. Output = state of the inputIf I.10 = 0 then: "remote via the bus" mode. Output = state of the register1743233 03/2008 33
Page 1: TeSys U LUTM ControllerUser Manual0
Page 6 and 7: Safety InformationPLEASE NOTEElectr
Page 8 and 9: About the BookProduct RelatedWarnin
Page 10 and 11: Setting Up the LUTM ControllerWhat'
Page 12 and 13: Setting Up the LUTM ControllerDescr
Page 14 and 15: Setting Up the LUTM ControllerCompo
Page 16 and 17: Setting Up the LUTM ControllerLUC
Page 18 and 19: Setting Up the LUTM ControllerPrese
Page 20 and 21: Setting Up the LUTM ControllerAssem
Page 22 and 23: Setting Up the LUTM ControllerTrans
Page 24 and 25: Setting Up the LUTM ControllerParti
Page 26 and 27: Setting Up the LUTM ControllerStart
Page 28 and 29: Setting Up the LUTM ControllerSetti
Page 30 and 31: Operation of the LUTM controllerOpe
Page 34 and 35: Operation of the LUTM controllerAdd
Page 36 and 37: Operation of the LUTM controller3-w
Page 38 and 39: Operation of the LUTM controllerCon
Page 40 and 41: Operation of the LUTM controllerSta
Page 42 and 43: Operation of the LUTM controllerAck
Page 44 and 45: Operation of the LUTM controllerAla
Page 46 and 47: Technical characteristics of the LU
Page 48 and 49: Technical characteristics of the LU
Page 50: GlossaryEExternal faultThe tripping
Page 54: You can download this technical pub

TeSys U LUTM Controller User Manual 03/2008 - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?