TeSys U LUTM Controller User Manual 03/2008 - Schneider Electric

More documents

Recommendations

Info

Operation of the LUTM controllerAdditional Inputs3 inputs can be used in addition to those already mentioned during operation witha communication module.Input Function CommentThis input is dedicated.I.7 SRIt is used to communicate the system availability via the bus. Example: receipt of the data provided by(SystemHowever if the mapping "Ready" bit is not used, I.7 is the circuit-breaker "Ready" NO contact.Ready)available for feeding back any other data item.I.8 This input is used to send back external data via the Example: "emergency stop button status".communication bus (writing to a register).Example: in the case of a control panelI.9It has no effect on controller operation.with "rack in test position".Control ofOutputs 13 and 23Control of outputs 13 and 23 of the LUTM controller depends on the selectedoperating mode. (Refer to the documentation for the communication module)"Local" mode"Remote via thebus" mode."Mixed" mode(input I.10manages thepriorities)OperationCommentOutputs 13 and 23 are only controlled by inputs I.1 and I.2.Commands via the bus are not taken into account.Outputs 13 and 23 are only controlled by the bus.The state of inputs I.1 and I.2 does not affect outputs 13 and 23."Local" mode if I.10 = 1"Remote via the bus" mode ifI.10 = 0Outputs 13 and 23 are only controlled by inputs I.1 and I.2.Commands via the bus are not taken into account.Outputs 13 and 23 are only controlled by the bus, from the PLC.The state of inputs I.1 and I.2 does not affect outputs 13 and 23.Note: Commands transmitted during communication are passed directly to theoutput relays, without wiring between the communication module outputs andinputs I.1 and I.2.Note: Even when there is a control unit fault or external fault condition, outputs 13and 23 can still be controlled. Their state is not necessarily "open", even if thecommunication module is faulty.34 1743233 03/2008
Operation of the LUTM controllerExamples ofApplicationsControl with "remote via the bus" operating mode.3671 23 451 Channel 12 Channel 23 Any fault4 Control unit fault5 External fault6 Network connection7 Communication moduleNote: To feed back external data via the communication bus (write to a register)using inputs I.1 and I.2, operation must be configured in "remote via the bus"mode. (Refer to the documentation for the communication module)3-wire control with "local" or "remote via the bus" operating mode and datafeedback (pushbutton voltage: 24 V ).3671 23 4851 Channel 12 Channel 23 Any fault4 Control unit fault5 External fault6 Network connection7 Communication module8 "Local"/"remote via the bus"1743233 03/2008 35
Page 1: TeSys U LUTM ControllerUser Manual0
Page 6 and 7: Safety InformationPLEASE NOTEElectr
Page 8 and 9: About the BookProduct RelatedWarnin
Page 10 and 11: Setting Up the LUTM ControllerWhat'
Page 12 and 13: Setting Up the LUTM ControllerDescr
Page 14 and 15: Setting Up the LUTM ControllerCompo
Page 16 and 17: Setting Up the LUTM ControllerLUC
Page 18 and 19: Setting Up the LUTM ControllerPrese
Page 20 and 21: Setting Up the LUTM ControllerAssem
Page 22 and 23: Setting Up the LUTM ControllerTrans
Page 24 and 25: Setting Up the LUTM ControllerParti
Page 26 and 27: Setting Up the LUTM ControllerStart
Page 28 and 29: Setting Up the LUTM ControllerSetti
Page 30 and 31: Operation of the LUTM controllerOpe
Page 32 and 33: Operation of the LUTM controllerExa
Page 36 and 37: Operation of the LUTM controller3-w
Page 38 and 39: Operation of the LUTM controllerCon
Page 40 and 41: Operation of the LUTM controllerSta
Page 42 and 43: Operation of the LUTM controllerAck
Page 44 and 45: Operation of the LUTM controllerAla
Page 46 and 47: Technical characteristics of the LU
Page 48 and 49: Technical characteristics of the LU
Page 50: GlossaryEExternal faultThe tripping
Page 54: You can download this technical pub

TeSys U LUTM Controller User Manual 03/2008 - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?