TeSys U LUTM Controller User Manual 03/2008 - Schneider Electric

More documents

Recommendations

Info

Operation of the LUTM controllerAlarmAcknowledgmentAlarmsList of possible alarms.460AlarmnumberRegisters LULC• LUCM• LUTM461Alarm bitAlarmacknowledgementThermal overload alarm 3 _.3 = 1 -"ERR" (line 1) "FAULT"Overloadalarm-Automatic when theoverload is less than85%Loss of communication withthe LULC• communicationmodule alarm109(notapplicable)FlashingFlashingComm loss Write: 703.3=1LUCM• multifunction controlunit alarm2, 4to13Refer to the User’s Manualfor the LUCM••BL or LUCMT1BL multifunction control unit.Alarms460AlarmnumberRegisters LULC• LUCM• LUTM461Alarm bitAlarmacknowledgement"ERR" (line 1) "FAULT"LUTM external alarmindicated by I.6 changing to 0(with LULC•)201 _.15 = 1 - Warn-M201FlashingAutomatic with I.6returning to 1RestartFollowing LossofCommunicationAfter acknowledgment by setting bit 703.3 to 1, restart according to the states ofcontrol bits 704.0 and 704.1.44 1743233 03/2008
Technical characteristics of theLUTM controller3Technical CharacteristicsEnvironmentTable of the LUTM controller technical characteristics.CertificationConformity to standards IEC/EN 60947-4-1, UL 508, CSA C22-2 No. 14European communitydirectivesRated insulation voltage (Ui)Rated impulse withstandvoltage (Uimp)Degree of protectionaccording to IEC/EN 60947-1(protection against directfinger contact)Protective treatmentAmbient air temperaturearound the deviceMaximum operating altitudeUL, CSAmarking. Satisfies the essential requirements of the low voltage (LV) machinery andelectromagnetic compatibility (EMC) directives.According to IEC/EN 60947-1,overvoltage category III, degree ofpollution: 3V 240According to UL508, CSA C22-2 no. 14 V 240According to IEC/EN 60947-4-1 kV 4Front panel (outside connection zone) IP 40Front panel and wired terminals IP 20Other sides IP 20According to IEC/EN 60068"TH"According to IEC/EN 60068-2-30 Cycles 12According to IEC/EN 60068-2-11 h 48StorageOperation°C°F°C°F°C°Fmft- 40 + 85- 40 + 185- 25 + 70 (LUCBT/DT/LUTM)- 13 + 160 (LUCBT/DT/LUTM)- 25 + 60 (LUCMT, LULC•)- 13 + 140 (LUCMT, LULC•)200065601743233 03/2008 45
Page 1: TeSys U LUTM ControllerUser Manual0
Page 6 and 7: Safety InformationPLEASE NOTEElectr
Page 8 and 9: About the BookProduct RelatedWarnin
Page 10 and 11: Setting Up the LUTM ControllerWhat'
Page 12 and 13: Setting Up the LUTM ControllerDescr
Page 14 and 15: Setting Up the LUTM ControllerCompo
Page 16 and 17: Setting Up the LUTM ControllerLUC
Page 18 and 19: Setting Up the LUTM ControllerPrese
Page 20 and 21: Setting Up the LUTM ControllerAssem
Page 22 and 23: Setting Up the LUTM ControllerTrans
Page 24 and 25: Setting Up the LUTM ControllerParti
Page 26 and 27: Setting Up the LUTM ControllerStart
Page 28 and 29: Setting Up the LUTM ControllerSetti
Page 30 and 31: Operation of the LUTM controllerOpe
Page 32 and 33: Operation of the LUTM controllerExa
Page 34 and 35: Operation of the LUTM controllerAdd
Page 36 and 37: Operation of the LUTM controller3-w
Page 38 and 39: Operation of the LUTM controllerCon
Page 40 and 41: Operation of the LUTM controllerSta
Page 42 and 43: Operation of the LUTM controllerAck
Page 46 and 47: Technical characteristics of the LU
Page 48 and 49: Technical characteristics of the LU
Page 50: GlossaryEExternal faultThe tripping
Page 54: You can download this technical pub

TeSys U LUTM Controller User Manual 03/2008 - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?