general recommendations - safety - AJ Maskin AS

More documents

Recommendations

Info

6.3.5 - Steering funtioning3 Repair manualIn the hydraulic block input, the oil first passes through a priority valve. The latterpowers steering through a priority flow.It is necessary that YV1 be at rest (Travel selection)The choice of YV5A or B depends on the direction requested for steering.Right or left cylinder power supply outputaccording to the direction requested.Priority flowPriority valveNon priority flowPump output flowFilter onreturnHydraulic tank: 27 l / 7 gallonMotor pumprun by thechopper44
Repair manual 37 - MAINTENANCE7.1 - GENERAL RECOMMENDATIONSCaution!Do not use the machine as awelding ground.Do not weld withoutdisconnecting the (+) and (-)battery terminals.Do not start other vehicleswith the batteries connected.Servicing operations described in this manual are given for normal conditions ofuse.In difficult conditions: extreme temperatures, high hygrometry, pollutedatmosphere, high altitude, etc., certain operations must be carried out morefrequently and specific precautions must be taken: consult the PINGUELYHAULOTTE After-Sales Service for information.Only authorised and competent personnel may operate on the machine and mustcomply with the safety instructions related to Personnel and Environmentprotection.Regularly check that the safety systems work properly:1°) Tilt: buzzer + stop (travel and lifting disabled).2°) Platform overload - load.7.2 - MAINTENANCE DEVICEThe maintenance stand enables the operator to work under the machine in totalsafety.Photo 2Operating instructions:(Photo 2, page 45)These operations are to be carried out on both sides of the platform.Putting the maintenance stand into place:• Position the platform on a firm, horizontal floor.• Ensure that the two emergency stop buttons are "ON".• Turn the chassis ignition key to the "Chassis" position.• Push the chassis lifting switch up to raise the platform.• Unscrew and turn the maintenance stand and allow to hang vertically.• Push the lifting switch down to lower the platform gradually until the maintenancestand comes up against the two fixing points (top and bottom).Removing the maintenance stand:• Push the chassis lifting switch up and gradually raise the platform until themaintenance stand is free.• Turn the maintenance stand until it comes into its storage position and screwback into place.• Push the chassis lifting switch down and lower the platform completely.45
Page 1: REPAIR MANUALSELF-PROPELLED SCISSOR
Page 6: 21 Repair manual
Page 9 and 10: Repair Manual10 - CORRECTIVE MAINTE
Page 11 and 12: Repair manual 31 - GENERAL RECOMMEN
Page 13 and 14: Repair manual 3To avoid all risk of
Page 15 and 16: Repair manual 3NB:In the case of re
Page 17 and 18: Repair manual 32 - SPECIFICATIONSel
Page 19 and 20: 78590Repair manual 32.2 - SIZE2.2.1
Page 21 and 22: Repair manual 32.4 - PRESSURE TABLE
Page 23 and 24: Repair manual 33 - WIRING DIAGRAM17
Page 25 and 26: Repair manual 33.1.1 - Electric com
Page 27 and 28: Repair manual 33.2.1 - Electric com
Page 29 and 30: Repair manual 34 - ELECTRIC COMPONE
Page 31 and 32: Repair manual 34.4 - END OF TRAVEL
Page 33 and 34: Repair manual 34.7 - USING THE ON-B
Page 35 and 36: Repair manual 35 - HYDRAULIC DIAGRA
Page 37 and 38: Repair manual 35.2.1 - Components l
Page 39 and 40: Repair manual 36 - DESCRIPTION OF T
Page 41 and 42: Repair manual 36.2 - MK4 HYDRAULIC
Page 43 and 44: Repair manual 3FRONT VIEW37
Page 45 and 46: Repair manual 36.2.1 - List of comp
Page 47 and 48: Repair manual 36.3.4 - Speed select
Page 49: Repair manual 3LoweringPotholes’
Page 53 and 54: Repair manual 37.4.2 - Maintenance
Page 55 and 56: Repair manual 3REMINDER:All these f
Page 57 and 58: Repair manual 38 - PREVENTIVE MAINT
Page 59 and 60: SHEET P001PREVENTIVE MAINTENANCE SH
Page 67 and 68: Repair manual 39 - OPERATING INCIDE
Page 69 and 70: Repair manual 39.1.3 - Travel syste
Page 71 and 72: Repair manual 3AlarmcodeNumberoffla
Page 73 and 74: Repair manual 39.2 - FAILURE DETECT
Page 75 and 76: SHEET DP001FAILURE DETECTION FLOW C
Page 101 and 102:
FAILURE DETECTION FLOW CHARTSHEET D
Page 103 and 104:
FAILURE DETECTION FLOW CHARTSHEET D
Page 105 and 106:
SHEET DP061FAILURE DETECTION FLOW C
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Repair manual10 - CORRECTIVE MAINTE
Page 113 and 114:
CORRECTIVE MAINTENANCE SHEETSHEET C
Page 115 and 116:
SHEET C002CORRECTIVE MAINTENANCE SH
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175:
2CORRECTIVE MAINTENANCE SHEETSHEET
show all

general recommendations - safety - AJ Maskin AS

Create successful ePaper yourself

Delete template?

Save as template?