PT Series Operator & Parts Manual - McConnel

More documents

Recommendations

Info

Flexible Couplings1) Short driveshaft clamp bolt (2 off)2) Flexible coupling (2 off)3) Flexible coupling mounting bolts (12 off)4) Long driveshaft (2 off)Check each flexible coupling for damage and cracks. Replace if any damage is found.Check the tightness of the short driveshaft clamping bolt and coupling mounting bolts to thecorrect torque. Repeat with the other drive coupling. Refer to ‘Specific Torque Settings’chart.WARNING: Ensure that the opposing blade carriers and blades are at 90° to each other afterany maintenance that requires removing or replacing drive couplings.39
Blade Carrier & Blade MaintenanceWARNING: Ensure that the machine is safely supported using suitable lifting and supportequipment before attempting to work beneath a machine – never use or rely on the tractor’shydraulic system to support the machine.Blade Carrier Removal Lift and support the machine on safety supports. With assistance, support the blade carrier, remove the split pin and rotor castle nut andremove the rotor from the splined gearbox output shaft. Refer to photo below. With assistance, remove the four nuts and mounting bolts securing the gearbox to themachine. Remove the gearbox.1) Blade Carrier mounting bolts and nuts2) Rotor hub castle nutBlade Carrier ReplacementReplacement is the reverse of removal procedure stated above - tighten the mounting boltsand castle nut as specified in ‘Specific Torque Settings’ chart.Blade Carrier MaintenanceCheck the rotor hub for slack. Some settlement may occur after the first hours of working.Re-tighten the castle nut one quarter of a turn at a time, and back off until the split pin can befitted. Repeat until the slackness is removed. Check the blade carrier mounting bolts fortightness - Refer to ‘Specific Torque Settings’ chart.40
Page 4 and 5: 2. REMEDIES AND PROCEDURES2.01. The
Page 6: ROTARY MOWER INSPECTION AND MAINTEN
Page 11 and 12: TRACTOR PRE-OPERATION InspectionPow
Page 14: LIST OF CONTENTSPage No.Operation S
Page 17 and 18: PT240 ModelA) Machine Body/DeckB) G
Page 19 and 20: SPECIFICATIONSDescription PT180 Mod
Page 21 and 22: The operator and all support person
Page 23 and 24: Ensure that a PTO shield is install
Page 25 and 26: LOCATION OF SAFETY & INSTRUCTIONAL
Page 27 and 28: UNPACKING THE MACHINE - PT180 Model
Page 29 and 30: UNPACKING THE MACHINE - PT270 Model
Page 31 and 32: ATTACHING THE MACHINE - PT180 Model
Page 37 and 38: PTO DRIVESHAFT INSTALLATIONThe PTO
Page 39 and 40: TRANSPORTING THE MACHINEFor transpo
Page 41 and 42: MOVING FROM TRANSPORT TO WORK POSIT
Page 43 and 44: MACHINE OPERATIONOperating the Mach
Page 45 and 46: Headstock Position (PT180 Models on
Page 47 and 48: CLEANING THE MACHINECleaning Proced
Page 49 and 50: Maintenance SafetyWARNING: Before a
Page 51 and 52: Gearboxes & Couplings Maintenance -
Page 53: Draining & RefillingTo drain oil fr
Page 57 and 58: LUBRICANTSRecommended LubricantsSup
Page 60 and 61: PARTS MANUALPT180 / 240 / 270PASTUR
Page 62 and 63: DECK MODULE - PT180 ModelsModule(s)
Page 64 and 65: DECK & COVERS MODULES - PT240 Model
Page 66 and 67: COVER MODULE - PT270 ModelsModule(s
Page 68 and 69: SKIDS MODULE - PT240 & PT270 Models
Page 70 and 71: PTO MODULE - PT180 ModelsModule(s):
Page 72 and 73: DRIVE MODULE - PT270 ModelsModule(s
Page 74 and 75: ROTOR MODULE - PT180 ModelsModule(s
Page 76 and 77: ROTOR MODULE - PT270 ModelsModule(s
Page 78 and 79: BASIC DECAL KIT - PT240 & 270 Model
Page 80 and 81: SPECIFIC DECAL KIT - PT240 ModelsMo
Page 82: STACKING LEGS - PT180, PT240 & PT27

PT Series Operator & Parts Manual - McConnel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?