Tab 36

More documents

Recommendations

Info

36.5Adjustable Frequency DrivesH-Max Series Drives363636363636363636363636363636363636363636363636363636363636Technical Data and SpecificationsH-Max Series DrivesDescriptionSpecificationInput RatingsInput voltage (V in ) 200–240 Vac, 380–480 Vac, –10%/+10%Input frequency (f in ) 50/60 Hz (variation up to 47–66 Hz)Connection to power Once per minute or less (typical operation)Short circuit withstand 100 kAICratingOutput RatingsOutput voltage0 to V in /U in line voltage inContinuous output current Ambient temperature max. 104°F (40°C)I L overload1.1 x I L (1 min./10 min.)Overload current110% (1 min./10 min.)Initial output current 150% for two secondsOutput frequency0 to 320 HzFrequency resolution 0.01 HzControl CharacteristicsControl methodFrequency control (V/f) open loop sensorless vector controlSwitching frequency 1–310 ampsFS4–9: default 6 kHzFrequency reference Analog input: Resolution 0.1% (10-bit), accuracy ±1%Panel reference: Resolution 0.01 HzField weakening point 8 to 320 HzAcceleration time 0.1 to 3000 secondsDeceleration time 0.1 to 3000 secondsBraking torqueDC brake: 30% x T n (without brake option)Ambient ConditionsAmbient operatingtemperatureStorage temperatureRelative humidityFS4–FS9: 14°F (–10°C), no frost to 104°F (40°C)(Drive can operate at 122°F (50°C), see Pages V6-T36-141 andV6-T36-142)–40° to 158°F (–40° to 70°C)0 to 95% RH, noncondensing, non-corrosive, no dripping waterAir quality Chemical vapors: IEC 60721-3-3, unit in operation, Class 3C2;Mechanical particles: IEC 60721-3-3, unit in operation, Class 3S2Altitude100% load capacity (no derating) up to 3280 ft (1000m);1% derating for each 328 ft (100m) above 3280 ft (1000m);max. 9842 ft (3000m); 380–480VVibrationFS4–FS9: EN 61800-5-1, EN 60068-2-6; 5 to 150 Hz,displacement amplitude 1 mm (peak) at 5 to 15.8 Hz,max. acceleration amplitude 1G at 15.8 to 150 HzShockEN 61800-5-1, EN 60068-2-27 UPS Drop test (for applicable UPSweights) Storage and shipping: max. 15G, 11 ms (in package)Enclosure classNEMA Type 1/IP21 or NEMA Type 12/IP54(keypad required for IP54/Type 12)StandardsEMCImmunity: Fulfills all EMC immunity requirements;Emissions: EN 61800-3, LEVEL H (EMC C2)EmissionsEMC level dependent—+EMC 2: EN61800-3 (2004) Category C2Delivered with Class C2 EMC filtering as default.DescriptionControl ConnectionsAnalog input voltageAnalog input currentDigital inputs (6)Auxiliary voltageOutput reference voltageAnalog outputRelay outputsHard wire jumperDip switch setting defaultSpecification0 to 10V, R = 200 kohms differentialResolution 0.1%; Accuracy ±1%Dip switch selection (voltage/current)0(4) to 20 mA; R i –250 ohms differentialPositive or negative logic; 18 to 30 Vdc+24V ±10%, max. 250 mA+10V +3%, max. load 10 mA0–10V, 0(4) to 20 mA; R L max. 500 ohms;Resolution 10 bit; Accuracy ±2%Dip switch selection (voltage/current)3 programmable, 2 Form C, 1 Form A relay outputsSwitching capacity: 24 Vdc/8A, 250 Vac/8A, 125 Vdc/0.4ABetween terminal 6 and 10 factory defaultRS485 = offA01 = currentA12 = currentA11 = voltageProtectionsOvercurrent protection YesOvervoltage protection YesDC bus regulation anti-trip Yes (accelerates or decelerates the load)Undervoltage protection YesEarth fault protection Yes (in case of earth fault in motor or motor cable,only the frequency converter is protected)Input phase supervision Yes (trips if any of the input phases are missing)Motor phase supervision Yes (trips if any of the output phases are missing)Overtemperature protection YesMotor overload protection YesMotor stall protection YesMotor underload protection YesShort circuit protection YesSurge protectionYes (varistor input)Conformed coated Yes (prevents corrosion)(varnished) boardsSeismicOHSPD Special Seismic Certification Pre-ApprovedV6-T36-146Volume 6—Solid-State Motor Control CA08100007E—April 2011 www.eaton.com
Adjustable Frequency DrivesH-Max Series Drives36.5Wiring DiagramControl Input/Output, PID ApplicationOptionalCircuitBreakerFactoryJumperResistorAnalogRJ-45L1L2L3Slot ATerminal1 +10V2 AI–1+3 VinStandards● Digital inputs D1–D6, relayout, analog in/out are freelyprogrammed●The user can assign asingle input to multiplefunctions456789101112131415161718Three-Phase Input ReactorInput(Single-Phase not available)AI–2+AI–2–24VoutGNDDIN1DIN2DIN324VoutGNDDIN4DIN5DIN6AO–1+Factory Default SignalDBChopperThree-PhaseOutputReference OutputAnalog Input Voltage (Range 0–10 Vdc)(can be programmed to current 4–20 mA)Analog Output Common (Ground)Analog Input Current (Range 4–20 mA)(can be programmed to voltage 0–10 Vdc)PI Setpoint or FeedbackAnalog Input CommonPI Setpoint or FeedbackControl Voltage Output (0.1A max.)I/O GroundSTART/STOP (Contact closed = start)External Fault (Closed = fault)Run Interlock Permissive IP Interlock(Closed = OK)DIN1–DIN6 CommonControl Voltage Output (0.1A max.)I/O GroundSpeed Select 0–100% (Preset speed)Fire Mode (Contact closed = fire mode)Force Bypass (Contact closed = bypass)DIN1–DIN6 CommonOutput Frequency (0–20 mA)RO3 FaultIncludes● Six digital input● Two analog input●One analog output● Three relay output● RS-485●Ethernet (BACnet andModbus)R+R-1930AO–1–24 VdcinAnalog Output Common (Ground)Auxiliary Input VoltageA DATA- RS-485 DATA- Programmable BACnet,B DATA+ RS-485 DATA+Modbus, FLN, N221Relay Board 1 Slot BDefault Signal22RO1 Bypass Run232424 Vdc/8A250 Vac/8A25RO2 Drive Run125 Vdc/0.4A263233COMCMBBACnet/IP Ethernet Industrial ProtocolModbus/TCP Transmission Control Protocol (Ethernet Based)5% DC LinkU (T1)V (T2)W (T3)Slot D __________________OptionalResistor21RO1NC12 13 14 15 16 17 18 19 30 A B24 VdcoutGNDDI4DI5DI61 2 3 4 5 6 7 8 9 10 11+10Vdc22 23 24 25 26 32 33RO1COMAI1+MotorRO1NOAI1–ONCURRENTCURRENTCURRENTTerminal Block LayoutAI2+RO2NCAI2–Reliability● Pretested components● Conformal coated(varnished) boards● 40°C rated●110% overload for oneminute●Eaton Electrical Services &Systems national networkof AF drive specialistsTestRO2COMCOMDI1–624 VdcoutOFFVOLTAGEVOLTAGEVOLTAGERO2NOAO1+GNDAO1– 24 Vdc RS-485 RS-485in Data– Data+DI1RS485AO1AI2AI1RO3COMDI2Factory JumperExternal InterlockRO3NODI3COMDI1–6Slot E __________________363636363636363636363636363636363636363636363636363636363636Volume 6—Solid-State Motor Control CA08100007E—April 2011 www.eaton.comV6-T36-147
Page 2:
36.1Adjustable Frequency DrivesNFX9
Page 13 and 14:
Adjustable Frequency DrivesM-Max Se
Page 15 and 16:
Adjustable Frequency DrivesSVX9000
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37:
Page 40 and 41:
36.3Adjustable Frequency DrivesSVX9
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96: Adjustable Frequency DrivesSVX9000
Page 97 and 98: Adjustable Frequency DrivesSVX9000
Page 99 and 100: Adjustable Frequency DrivesSPX9000
Page 139 and 140: Adjustable Frequency DrivesH-Max Se
Page 145: Adjustable Frequency DrivesH-Max Se
Page 159 and 160: Adjustable Frequency DrivesCFX9000
Page 193 and 194: Adjustable Frequency DrivesCPX9000
Page 195 and 196: Adjustable Frequency DrivesCPX9000
Page 197 and 198:
Adjustable Frequency DrivesCPX9000
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Adjustable Frequency DrivesLCX9000
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Adjustable Frequency DrivesSPA9000/
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
show all

Tab 36

Create successful ePaper yourself

Delete template?

Save as template?