IPR-12 Manual - Scintrex

More documents

Recommendations

Info

KEYPAD AND DISPLAY DESCRIPTIONSOutput DisplayThe Output display enables you to select specific parameters for outputting datato a peripheral device. This display is accessible from the Main Menu.DUMP PARAMETERS:BAUD RATE: rDATA BITS:CR DELAY:DUMP ONE LINEDUMP ALL DATA:CLEAR MEMORY:j 300 (1)c 600 (2)1200 (3)? 2400 (4)? 4800 (5)600 (6)? 19200 (7)38400 (8)57600 (9)Change ?BAT1: bbbDATA BITS - This is the number of data bits output during the data dump. Youcan select either 7 or 8 data bits. These must be selected according to yourexternal device. This is usually achieved by experimenting with each data bitselection.BAUD RATE - This is the speed at which the data is sent to the external device.This rate must correspond to the rate at which your external device can acceptdata. The current baud rate setting is shown after the prompt (r) while theselections that are available are shown below.CR DELAY - This delay slows down the carriage return signal for slow printersso the data of the next line is not sent prematurely. The range is from 0 to 999msand depends on your printer. The delay is usually established by experimenting.Computers usually accept a delay of 0.DUMP ONE LINE - This selection enables you to dump the data one line at atime. The line that you are dumping is shown in the Locations display underRecall. If you want to dump the next line in the sequence, you do not have toreturn to the Locations display to change the line, you can just press the Enterkey. The IPR-12 will automatically advance to the next line number and dumpthe data.DUMP ALL DATA -This parameter is selected to start the data dump. Itoutputs all of the data at one time, possibly into a very large file.3-10
KEYPAD AND DISPLAY DESCRIPTIONSCLEAR MEMORY - This parameter is selected to clear the memory andrequires a (Y)es or (N)o answer. Once you clear the memory by selecting 'Y' allof the data is lost, except for the setup parameters.Signal-NoiseThe Signal-Noise Monitor display shows the signal of a selected dipoleM onitor Displayin order to help you troubleshoot if you encounter a problem. This display isavailable from the Main Menu.Figure 5: Example of Signal-Noise DisplayNotes:• The input signals are sampled at 50ms intervals and the data value of theselected dipole displayed as a pixel on the display. This enables you to observesignal, noise and SP drift for up to approximately 12 seconds at a time. The fullscale value can be changed in 1-2-5 steps. The SP can also be removed in orderto observe the small noise on top of a large SP.DIP. # - This is the number of the selected dipole for which the display applies.Full Scale - The full scale value (+xx) is the - vertical value of the box outline.You can adjust the value to between +1mV to +14V.3-11
Page 2 and 3: TABLE OF CONTENTSIntroductionDescri
Page 5 and 6: TABLE OF CONTENTS4.0 SETTING UP THE
Page 7 and 8: TABLE OF CONTENTSCole-Cole Paramete
Page 9 and 10: INTRODUCTIONINSTRUMENT OVERVIEWThe
Page 11 and 12: INTRODUCTIONSYSTEM COMPONENTSThe IP
Page 13 and 14: GETTING STARTEDINSPECTING YOUR IPR-
Page 15 and 16: KEYPAD AND DISPLAY DESCRIPTIONSTHE
Page 17 and 18: KEYPAD AND DISPLAY DESCRIPTIONSNume
Page 19 and 20: KEYPAD AND DISPLAY DESCRIPTIONSSetu
Page 21 and 22: KEYPAD AND DISPLAY DESCRIPTIONSIn i
Page 23: KEYPAD AND DISPLAY DESCRIPTIONSCust
Page 27 and 28: KEYPAD AND DISPLAY DESCRIPTIONSC-LI
Page 29 and 30: KEYPAD AND DISPLAY DESCRIPTIONSBAT1
Page 31 and 32: KEYPAD AND DISPLAY DESCRIPTIONS12¯
Page 33 and 34: KEYPAD AND DISPLAY DESCRIPTIONSNume
Page 35 and 36: KEYPAD AND DISPLAY DESCRIPTIONSThe
Page 37 and 38: SETTING UP THE IPR-12SET-UP PROCEDU
Page 39 and 40: SETTING UP THE IPR-12SelectIf the p
Page 41 and 42: SETTING UP THE IPR-1234. Toggle unt
Page 43 and 44: SETTING UP THE IPR-12Note: 0 is usu
Page 45 and 46: SETTING UP THE IPR-1227. Select +Se
Page 47 and 48: SETTING UP THE IPR-12Note: If you e
Page 49 and 50: OPERATING PROCEDURESOPERATING PROCE
Page 51 and 52: OPERATING PROCEDURESOn-Line Procedu
Page 53 and 54: OPERATING PROCEDURESRecall 1. In th
Page 55 and 56: OPERATING PROCEDURESThe Display Hea
Page 57 and 58: OPERATING PROCEDURESEXAMPLE OF A DA
Page 59 and 60: CONNECTING THE ELECTRODESCONNECTING
Page 61 and 62: CONNECTING THE ELECTRODESUsing TheM
Page 63 and 64: MEASUREMENTS AND CALCULATIONSIPR-12
Page 65 and 66: MEASUREMENTS AND CALCULATIONSlarge
Page 67 and 68: MEASUREMENTS AND CALCULATIONS2 -10
Page 69 and 70: MAINTENANCE AND TROUBLESHOOTINGMAIN
Page 71 and 72: MAINTENANCE AND TROUBLESHOOTINGThe
Page 73 and 74: MAINTENANCE AND TROUBLESHOOTINGTROU
Page 75 and 76:
MAINTENANCE AND TROUBLESHOOTINGHeat
Page 77 and 78:
SPECIFICATIONSTransmitter Timing:Eq
Page 79 and 80:
APPENDICESAPPENDIX A: NOISE SOURCES
Page 81 and 82:
APPENDICES- P2 is the reference- P1
Page 83 and 84:
APPENDICES2. 0 Cole-Cole Parameter
Page 85 and 86:
APPENDICESis as if both amplitude a
Page 87 and 88:
APPENDICESthe phase angle curves ov
Page 89 and 90:
APPENDICES3.1 Use Of Cole-Cole Para
Page 91 and 92:
APPENDICESexamples from c=0.25 is r
Page 93 and 94:
APPENDICESused in mineral discrimin
Page 95 and 96:
APPENDICEScurves. Even a small amou
Page 97 and 98:
APPENDICESRMS difference values. Wi
Page 99 and 100:
APPENDICESknowing that the limit in
Page 101 and 102:
APPENDICES10-23
Page 103 and 104:
APPENDICESWhat is DOWNLOAD?Will DOW
Page 105 and 106:
APPENDICESAPPENDIX D:LISTA File and
Page 107 and 108:
APPENDICES* Toggles the start filer
Page 109 and 110:
APPENDICESDescriptionPart No.IPR-12
Page 111 and 112:
APPENDICESPlease note: All equipmen
Page 113 and 114:
APPENDICES8 80 230 270.03109 140 31
Page 115 and 116:
APPENDICESRec eive Time = 16 second
Page 117 and 118:
TABLE OF CONTENTSNumeric Slice Disp
Page 119 and 120:
TABLE OF CONTENTSUse of Cole-Cole P
Page 121 and 122:
Direction 3-10, 4-7Display 1-1, 1-3
Page 123:
RHO 3-19RMS 3-19Schlumberger1-1Self
show all

IPR-12 Manual - Scintrex

Create successful ePaper yourself

Delete template?

Save as template?