IPR-12 Manual - Scintrex

More documents

Recommendations

Info

SETTING UP THE IPR-1212. Enter the day.Setting Job # 13. Press the → or ↑ key to move the cursor to JOB #.14. Enter the job number.Setting The 15. Move the cursor to OPERATOR.Operator16. Push Change. The following prompt appears along the bottom line of the display:Enter name (9 ch)>17. Push the first letter or number key of the operator until the desired character appearsto the right of the prompt.Note: If you pr ess a wrong key, push the Clear key and re-enter the correct numberor letter.18.Press the Next key.19. Push the second letter or number key of the operator as in step 17.20. Press the Next key.21. Repeat steps 21 and 22 until the Operator designation is complete.22. Press Enter.Setting TheSerial Number23.24.Move the cursor to SERIAL #.Enter the serial number or any identification number.Selecting Test 25. Move the cursor to TEST26. Toggle until Yes appears.Selecting TheHeater27. Move the cursor to HEATER.28. Toggle until No appears.Setting TheDuration29.30.Move the cursor to DURATION.Enter 10.Setting The 31. Move the cursor to SYNC. CHANL.Sync. Channel32. Enter 1.Setting TheAutoRejection33. Move the cursor to AUTO REJ..4-4
SETTING UP THE IPR-1234. Toggle until No appears.Selecting The 35. Move the cursor to FULL SAT. DET.Full SaturationDetection36. Toggle until Yes appears.Setting 37. Move the cursor to TIMING.The Timing38. Select 2.Setting Mx 39. Move the cursor to Mx.40. Enter 340.41.Press the → key.42. Enter 520.Setting Cole- 43. Move the cursor to OMIT # SLICES.C ole Slices44. Enter 0.Setting 45. Move the cursor to UNIT.The Unit46. Toggle until Metre appears.The following is a typical Initialization Display:InitializationDisplayHH:MM:SS 12:00:00YY/MM/DD 91/06/24JOB #:OPERATOR:1024R. MILLERCOLE-COLE:OMIT # SLICES: 0SERIAL #: 9105002TIMING: 2TEST: YES UNITS: MetreHEATER:DURATION:NO10S YNC . CHANL.:AUTO REJ.:1NO VAR. SLICES: NoFULL SAT. DET. YES SLICE WIDTHS: -->Mx 340 - 520Custom Slice WidthSetup DisplayChange ?47. Move the cursor to Variable SlicesBAT: bbb4-5
Page 2 and 3: TABLE OF CONTENTSIntroductionDescri
Page 5 and 6: TABLE OF CONTENTS4.0 SETTING UP THE
Page 7 and 8: TABLE OF CONTENTSCole-Cole Paramete
Page 9 and 10: INTRODUCTIONINSTRUMENT OVERVIEWThe
Page 11 and 12: INTRODUCTIONSYSTEM COMPONENTSThe IP
Page 13 and 14: GETTING STARTEDINSPECTING YOUR IPR-
Page 15 and 16: KEYPAD AND DISPLAY DESCRIPTIONSTHE
Page 17 and 18: KEYPAD AND DISPLAY DESCRIPTIONSNume
Page 19 and 20: KEYPAD AND DISPLAY DESCRIPTIONSSetu
Page 21 and 22: KEYPAD AND DISPLAY DESCRIPTIONSIn i
Page 23 and 24: KEYPAD AND DISPLAY DESCRIPTIONSCust
Page 25 and 26: KEYPAD AND DISPLAY DESCRIPTIONSCLEA
Page 27 and 28: KEYPAD AND DISPLAY DESCRIPTIONSC-LI
Page 29 and 30: KEYPAD AND DISPLAY DESCRIPTIONSBAT1
Page 31 and 32: KEYPAD AND DISPLAY DESCRIPTIONS12¯
Page 33 and 34: KEYPAD AND DISPLAY DESCRIPTIONSNume
Page 35 and 36: KEYPAD AND DISPLAY DESCRIPTIONSThe
Page 37 and 38: SETTING UP THE IPR-12SET-UP PROCEDU
Page 39: SETTING UP THE IPR-12SelectIf the p
Page 43 and 44: SETTING UP THE IPR-12Note: 0 is usu
Page 45 and 46: SETTING UP THE IPR-1227. Select +Se
Page 47 and 48: SETTING UP THE IPR-12Note: If you e
Page 49 and 50: OPERATING PROCEDURESOPERATING PROCE
Page 51 and 52: OPERATING PROCEDURESOn-Line Procedu
Page 53 and 54: OPERATING PROCEDURESRecall 1. In th
Page 55 and 56: OPERATING PROCEDURESThe Display Hea
Page 57 and 58: OPERATING PROCEDURESEXAMPLE OF A DA
Page 59 and 60: CONNECTING THE ELECTRODESCONNECTING
Page 61 and 62: CONNECTING THE ELECTRODESUsing TheM
Page 63 and 64: MEASUREMENTS AND CALCULATIONSIPR-12
Page 65 and 66: MEASUREMENTS AND CALCULATIONSlarge
Page 67 and 68: MEASUREMENTS AND CALCULATIONS2 -10
Page 69 and 70: MAINTENANCE AND TROUBLESHOOTINGMAIN
Page 71 and 72: MAINTENANCE AND TROUBLESHOOTINGThe
Page 73 and 74: MAINTENANCE AND TROUBLESHOOTINGTROU
Page 75 and 76: MAINTENANCE AND TROUBLESHOOTINGHeat
Page 77 and 78: SPECIFICATIONSTransmitter Timing:Eq
Page 79 and 80: APPENDICESAPPENDIX A: NOISE SOURCES
Page 81 and 82: APPENDICES- P2 is the reference- P1
Page 83 and 84: APPENDICES2. 0 Cole-Cole Parameter
Page 85 and 86: APPENDICESis as if both amplitude a
Page 87 and 88: APPENDICESthe phase angle curves ov
Page 89 and 90: APPENDICES3.1 Use Of Cole-Cole Para
Page 91 and 92:
APPENDICESexamples from c=0.25 is r
Page 93 and 94:
APPENDICESused in mineral discrimin
Page 95 and 96:
APPENDICEScurves. Even a small amou
Page 97 and 98:
APPENDICESRMS difference values. Wi
Page 99 and 100:
APPENDICESknowing that the limit in
Page 101 and 102:
APPENDICES10-23
Page 103 and 104:
APPENDICESWhat is DOWNLOAD?Will DOW
Page 105 and 106:
APPENDICESAPPENDIX D:LISTA File and
Page 107 and 108:
APPENDICES* Toggles the start filer
Page 109 and 110:
APPENDICESDescriptionPart No.IPR-12
Page 111 and 112:
APPENDICESPlease note: All equipmen
Page 113 and 114:
APPENDICES8 80 230 270.03109 140 31
Page 115 and 116:
APPENDICESRec eive Time = 16 second
Page 117 and 118:
TABLE OF CONTENTSNumeric Slice Disp
Page 119 and 120:
TABLE OF CONTENTSUse of Cole-Cole P
Page 121 and 122:
Direction 3-10, 4-7Display 1-1, 1-3
Page 123:
RHO 3-19RMS 3-19Schlumberger1-1Self
show all

IPR-12 Manual - Scintrex

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?