SEL-751A Settings Sheets - CacheFly

More documents

Recommendations

Info

SET.36 of 66 SEL-751A Settings Sheets SET PORT p (p = F, 1, 2, 3, or 4) Command Date________________ SET PORT p (p = F, 1, 2, 3, or 4) Command PORT F PROTOCOL (SEL, MOD, EVMSG, PMU) PROTO := Communications SPEED (300, 1200, 2400, 4800, 9600, 19200, 38400 bps) SPEED := DATA BITS (7, 8 bits) (Hidden if PROTO := MOD, EVMSG, or BITS := PMU) PARITY (O, E, N) (Hidden if PROTO := EVMSG or PMU) PARITY := STOP BITS (1, 2 bits) (Hidden if PROTO := MOD or EVMSG) STOP := PORT TIME-OUT (0–30 min) (Hidden if PROTO := MOD, EVMSG, or PMU) HDWR HANDSHAKING (Y, N) (Hidden if PROTO := MOD or EVMSG) SEND AUTOMESSAGE (Y, N) (Hidden if PROTO := MOD, EVMSG, or PMU) T_OUT := RTSCTS := AUTO := Modbus MODBUS SLAVE ID (1–247) (Hidden if PROTO := SEL, EVMSG, or PMU) SLAVEID := PORT 1 (Ethernet Port in Slot B) (Hidden If Ethernet Option Not Included) IP ADDRESS (zzz.yyy.xxx.www) IPADDR := SUBNET MASK (zzz.yyy.xxx.www) SUBNETM := DEFAULT ROUTER (zzz.yyy.xxx.www) DEFRTR := Enable TCP Keep-Alive (Y, N) ETCPKA := TCP Keep-Alive Idle Range (1–20 sec) (Hidden if ETCPKA := N) KAIDLE := TCP Keep-Alive Interval Range (1–20 sec) KAINTV := (Hidden if ETCPKA := N) TCP Keep-Alive Count Range (1–20) (Hidden if ETCPKA := N) KACNT := FAST OP MESSAGES (Y, N) FASTOP := OPERATING MODE (FIXED, FAILOVER, SWITCHED) (Hidden if not dual redundant Ethernet Port option) FAILOVER TIMEOUT (0.10–65.00 sec) (Hidden if not dual redundant Ethernet Port option or if NETMODE is not set to FAILOVER) NETMODE := FTIME := PRIMARY NETPORT (A,B,D) (Hidden if not dual redundant NETPORT := Ethernet Port option) NETWRK PORTA SPD (AUTO,10,100 Mbps) (Hidden if not NETASPD := dual redundant Ethernet Port option) NETWRK PORTB SPD (AUTO,10,100 Mbps) (Hidden if not NETBSPD := dual redundant Ethernet Port option) TELNET PORT (23,1025–65534) TPORT := SEL-751A Relay Instruction Manual Date Code 20090501
Date _______________ SEL-751A Settings Sheets SET PORT p (p = F, 1, 2, 3, or 4) Command SET.37 of 66 TELNET TIME-OUT (1–30 min) TIDLE := FTP USER NAME (20 characters) FTPUSER := Enable IEC 61850 Protocol (Y, N) (Hidden if 61850 not E61850 := supported) Enable IEC 61850 GSE (Y, N) (Hidden if E61850 := N) EGSE := Enable Modbus Sessions (0–2) EMOD := Modbus TCP Port1 (1–65534) *(Hidden if EMOD := 0) MODNUM1:= Modbus TCP Port2 (1–65534) *(Hidden if EMOD := 0 or 1) MODNUM2:= * Exclude the following port numbers: 20 (FTP Data), 21 (FTP Control), TPORT setting, and DNPNUM setting if present. DNP3 Protocol All DNP3 settings below are Hidden if DNP3 is not an option. Enable DNP Sessions (0–3) (DNP3 settings below Hidden if EDNP := 0) EDNP := DNP TCP and UDP Port (1–65534) DNPNUM := DNP Address (0–65519) DNPADR := Session 1 IP Address {zzz.yyy.xxx.www} (15 characters) DNPIP1 := Transport Protocol (UDP, TCP) DNPTR1 := UDP Response Port (REQ, 1–65534) DNPUDP1 := DNP Address to Report to (0–65519) REPADR1 := DNP Map (1–3) DNPMAP1 := Analog Input Default Variation (1–6) DVARAI1 := Class for Binary Event Data (0–3) ECLASSB1 := Class for Counter Event Data (0–3) ECLASSC1 := Class for Analog Event Data (0–3) ECLASSA1 := Currents Scaling Decimal Places (0–3) DECPLA1 := Voltages Scaling Decimal Places (0–3) DECPLV1 := Misc Data Scaling Decimal Places (0–3) DECPLM1 := Amps Reporting Deadband Counts (0–32767) ANADBA1 := (Hidden if ECLASSA1 := 0) Volts Reporting Deadband Counts (0–32767) ANADBV1 := (Hidden if ECLASSA1 := 0) Misc Data Reporting Deadband Counts (0–32767) ANADBM1 := (Hidden if ECLASSA1 := 0 and ECLASSC1 := 0) Minutes for Request Interval (I, M, 1–32767) TIMERQ1 := Seconds to Select/Operate Time-Out (0.0–30.0) STIMEO1 := Seconds to send Data Link Heartbeat (0–7200) DNPINA1 := (HiddenifDNPTR1:=UDP) Event Message Confirm Time-Out (1–50 sec)) ETIMEO1 := Date Code 20090501 Instruction Manual SEL-751A Relay
Page 1 and 2: Date _______________ SEL-751A Setti
Page 35: Date _______________ SEL-751A Setti

SEL-751A Settings Sheets - CacheFly

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?