TSM Tool Stand

More documents

Recommendations

Info

Quick-Change Installation and Operation Manual Document #9610-20-1114-05 Foreword Please contact ATI Industrial Automation with any questions concerning your particular model. CAUTION: This manual describes the function, application, and safety considerations of this product. This manual must be read and understood before any attempt is made to install or operate the product, otherwise damage to the product or unsafe conditions may occur. Information contained in this document is the property of ATI Industrial Automation, Inc. (ATI) and shall not be reproduced in whole or in part without prior written approval of ATI. The information herein is subject to change without notice. This manual is periodically revised to reflect and incorporate changes made to the product. The information contained herein is confidential and reserved exclusively for the customers and authorized agents of ATI Industrial Automation and may not be divulged to any third party without prior written consent from ATI. No warranty including implied warranties is made with regard to accuracy of this document or fitness of this device for a particular application. ATI Industrial Automation shall not be liable for any errors contained in this document or for any incidental or consequential damages caused thereby. ATI Industrial Automation also reserves the right to make changes to this manual at any time without prior notice. ATI assumes no responsibility for any errors or omissions in this document. Users’ critical evaluation of this document is welcomed. ©Copyright by ATI Industrial Automation. All rights reserved. How to Reach Us Sale, Service and Information about ATI products: ATI Industrial Automation 1031 Goodworth Drive Apex, NC 27539 USA WWW.ati-ia.com Tel: 919.772.0115 Fax: 919.772.8259 E-mail: info@ati-ia.com Technical support and questions: Application Engineering Tel: 919.772.0115, Option 2, Option 2 Fax: 919.772.8259 E-mail: mech_support@ati-ia.com Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 2
Table of Contents Quick-Change Installation and Operation Manual Document #9610-20-1114-05 1. Safety.......................................................................................................................................... 7 1.1 Explanation of Notifications.......................................................................................................... 7 1.2 General Safety Guidelines............................................................................................................. 7 1.3 Safety Precautions......................................................................................................................... 8 2. Product Overview...................................................................................................................... 9 2.1 TSM System with Pin and Bushing Style Mounting.................................................................... 9 2.1.1 Post Modules..................................................................................................................... 10 2.1.2 Horizontal Modules............................................................................................................ 10 2.1.3 Pin and Bushing Mounting Module.................................................................................... 10 2.1.4 Tooling Interface Plates..................................................................................................... 11 2.1.5 Proximity Sensor Modules................................................................................................. 11 2.1.6 Tool Stand Interlock Switches, Trip Dogs, and Sipha Sensors.......................................... 12 2.2 TSM System with V-Block Style Mounting................................................................................. 12 2.2.1 Mounting Modules............................................................................................................. 13 2.2.2 Horizontal Extensions........................................................................................................ 13 2.2.3 Adapter Modules............................................................................................................... 14 2.2.4 Tooling Interface Plates..................................................................................................... 14 2.2.5 Vertical Mounting Module.................................................................................................. 15 2.2.6 Vertical Tooling Interface Plate.......................................................................................... 15 2.2.8 Sensor Holders.................................................................................................................. 15 2.2.9 Proximity Sensor............................................................................................................... 16 2.3 TSM System with Tool Hanger Mounting................................................................................... 16 2.3.1 Tool Hanger Mounting Modules......................................................................................... 17 2.3.2 Tool Hangers..................................................................................................................... 17 2.3.3 Proximity Sensor, and Cables for Tool Hanger Mounting Module..................................... 17 2.4 Post Module Components........................................................................................................... 18 2.4.1 Base Plate......................................................................................................................... 18 2.4.2 Rail Assemblies................................................................................................................. 19 2.4.3 Gusset Assembly............................................................................................................... 19 2.5 Determining The Tool Stand Configuration............................................................................... 20 2.5.1 Configuring a TSM System with Horizontal Mounting....................................................... 21 2.5.2 Configuring a TSM System with Pin and Bushing Mounting............................................. 21 2.5.3 Configuring a TSM System with Vertical Mounting........................................................... 22 2.5.4 Configuring a TSM System with Tool Hanger Mounting.................................................... 22 3. Installation............................................................................................................................... 23 3.1 Installing Base, Rail, and Gusset Assemblies........................................................................... 23 3.2 Installing Pin and Bushing or Horizontal V-Block Mounting Module to Tool Stand.............. 24 Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 3
Page 1: TSM Tool Stand Installation and Ope
Page 5 and 6: Quick-Change Installation and Opera
Page 15 and 16: 2.2.5 Vertical Mounting Module Quic
Page 17 and 18: 2.3.1 Tool Hanger Mounting Modules
Page 19 and 20: 2.4.2 Rail Assemblies Quick-Change
Page 27 and 28: 3.4 Installing Tool Hanger Mounting
Page 43 and 44: 8. Specifications Quick-Change Inst
Page 47 and 48: 9.4 Pin and Bushing Horizontal Blan
Page 53 and 54:
Quick-Change Installation and Opera
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
9.20 Vertical Tooling Interface Pla
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
9.30 Medium Tool Stand General Over
show all

TSM Tool Stand

Create successful ePaper yourself

Delete template?

Save as template?