TSM Tool Stand

More documents

Recommendations

Info

Quick-Change Installation and Operation Manual Document #9610-20-1114-05 3.9 Proximity Sensor installation for TSM Tool Hanger 1. Attach the proximity sensor to the mounting module by screwing the sensor into the bottom of the mounting module. Tighten to 6 in-lbs. 2. Position the sensor so the sensor face is flush with the surface of the mounting module. 3. Adjust sensor position as needed. 4. Tighten the jam nut on sensor against the mounting module. 5. Attach the sensor cable to the proximity sensor. Figure 3.10—Proximity Sensor Position for TSM Tool Hanger Mounting Module Proximity Sensor Jam Nut Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 32
Quick-Change Installation and Operation Manual Document #9610-20-1114-05 3.10 Installing a Tool Stand Interlock (TSI) Switch There are several many possible configuration, the following are samples of common Tool Stand Interlock switches: 3.10.1 Pin and Bushing Module with Tooling Interface Plate 1. Apply Loctite 242 ® to the four M5 socket head cap screws supplied with the Safety Switch. 2. Install the Safety Switch to the Tooling Interface Plate, as shown in Figure 3.11. 3. Secure the switch using the four M5 socket head cap screws. Tighten to 50 in-lbs. Note: The safety switch actuator arm can be reposition to the desired location refer to the manufacture instruction for repositioning the actuator. 4. Apply Loctite 242 ® to the two M8 socket head cap screws supplied with the Trip Dog. 5. Install the Trip Dog to the Pin and Bushing Module and secure with the two M8 socket head cap screws. Initially position the Trip Dog so that it will actuate the Safety Switch about 45° with the tooling secure in the Tool Stand. Note: Do not actuate the switch more than 75°. Snug the Screws to hold it position. 6. Connect the cable from the Safety Switch to the tool side control and signal module. 7. Cycle the tool pick-up and drop off and adjust the Trip Dog position to achieve the desired result. Tighten the two M8 socket head cap screws to 100 in-lbs. Figure 3.11—Installing a TSI Switch to a Pin and Bushing Module with a Tooling Interface Plate (4) M5 Socket Head Cap Screws Set initial trip position to 45 deg. TSI Trip Dog (2) M8 Socket Head Cap Screws Customer to set Switch Actuator Arm Orientation Safety Switch Vertical Tooling Interface Plate Pin and Bushing Module 3.11 Installing a Debris Shield Refer to http://www.ati-ia.com/App_Content/Documents/9610-20-1058.pdf#page=27. Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 • www.ati-ia.com • Email: info@ati-ia.com 33
Page 1 and 2: TSM Tool Stand Installation and Ope
Page 3 and 4: Table of Contents Quick-Change Inst
Page 5 and 6: Quick-Change Installation and Opera
Page 15 and 16: 2.2.5 Vertical Mounting Module Quic
Page 17 and 18: 2.3.1 Tool Hanger Mounting Modules
Page 19 and 20: 2.4.2 Rail Assemblies Quick-Change
Page 27 and 28: 3.4 Installing Tool Hanger Mounting
Page 31: Quick-Change Installation and Opera
Page 43 and 44: 8. Specifications Quick-Change Inst
Page 47 and 48: 9.4 Pin and Bushing Horizontal Blan
Page 63 and 64: 9.20 Vertical Tooling Interface Pla
Page 75 and 76: 9.30 Medium Tool Stand General Over

TSM Tool Stand

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?