Imatest Documentation

Recommendations

Info

Imatest Documentation '' (overexposed 2 stops, with filter) Canon 90mm f/2.8 TS-E (no filter) Sigma 18-125mm f/2.5-5.6 DC (hood, multi-coated UV filter) Canon 28-80mm f/3.5-5/6 (no filter) Canon 70-200mm f/4L USM (UV filter, hood) 0.464% 6 5 90 8 0.291% 15 14 77 8 0.293% 10 9 80 8 0.634% A very high quality tilt/shift lens with relatively few elements and groups. Has beautiful tonality and color quality. Low veiling glare expected. A remarkably fine lens for the price. Surprisingly low veiling glare. (If you're thinking of buying one: it has poor autofocus performance; it's much better on manual.) (1991 version) A cheap "kit" lens, designed for low cost. Expectations were low. Strangely reddish white balance. 16 13 70 8 0.396% Excellent lightweight lens. The IS version has 20 elements in 15 groups, which will increase flare. The table at the bottom shows the relationship between the number of groups (sets of attached elements) and the number of reflections that contribute to veiling glare. Most of the results are not surprizing. The Canon 90mm has the lowest flare, while the cheap Canon 28-80 is the worst. The only surprise is the excellent performance of the Sigma 18-125: a lens know for its fine performance and value, though its autofocus performance is mediocre. I use mine on manual. Limitations The veiling glare may be underestimated for telephoto lenses— especially if they are measured without lens hoods— because telephoto lenses form an image of only a small fraction of the light reaching the front element (the portion is much larger with normal and wide angle lenses). The target, as shown above, may not be large enough to simulate all the light that reaches the lens. If a hood is used, this error is considerably reduced. If there are nonlinearities in the camera response at low light levels, the results may be incorrect (although relative results, i.e., comparisons, will still be valid). It's always safest to work with RAW images and convert them with a "linear" (i.e., simple gamma curve) setting. You can read many RAW formats into Imatest, using the dcraw converter. ISO 9358 Lens elements, groups, reflections, and flare— some geeky math fun Lens flare is closely related to the number of secondary reflections in a lens, i.e., light entering the lens that is reflected off one lens surface, then another, then back to the image plane. For uncoated air-to-glass surfaces, about 4% of the incident light is reflected. Simple coating reduces the reflection to around 2%; muti-coating reduces it to 1% or less. For a simple coating, the amount of the secondary reflection is 0.02 * 0.02 = 0.0004, which doesn't seem like much until you calculate the number of reflections. A lens consists of N elements in M groups, where a group may consist of several elements cemented together. It's the number of groups M— actually the number of air-to-glass surfaces 2M— that really counts. The first surface has no secondary reflection. The second surface has 1: light that bounces off the second surface, then the first, then back to the image plane. Continuing with this reasoning, we see that the m(th) surface has m-1 secondary reflections, i.e., Total reflections = R = (2M-1) + (2M-2) + (2M-3) + ... + 1 = M (2M-1) = 2M 2 -M If you add a filter to a lens with M groups, you increase the number of reflections R by 4M+1. Groups M 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Reflections R 1 6 15 28 45 66 91 120 153 190 231 276 325 378 Zooms typically have more elements than primes. Examples (easy to locate in the Canon Museum): The Canon 24-105mm f/4L IS USM has 18 elements in 13 groups. The Canon 50mm f/1.4 USM has 7 elements in 6 groups. The Canon 90mm f/2.8 TS-E has 6 elements in 5 groups. Now you know one reason primes are still used (others are large apertures, light weight, and excellent sharpness (MTF)), as well as why some photographers avoid using filters (though a UV filter is useful protection for field work). Veiling glare, as measured by Imatest, is very similar to the veiling glare index (VGI) specified in the integral (black patch) test of the ISO 9358 standard, as described in Controlling Veiling Glare in an Optical Imaging System by Amber Czajkowski (University of Arizona). The key differences are The ISO standard calls for more rigorous testing conditions. In particular, an integrating sphere must be used. This means that there will be more light from outside the field of view, which will sometimes result in higher readings. The ISO standard does not include a step chart in the image. This means that only raw files (or files where the tonal response, i.e., OECF, is very well characterized) should be used. 46 of 451
Imatest Documentation Czajkowski' report contains a description of a really neat do-it-yourself integrating sphere project, based on stainless steel balls from http://www.gazingballoutlet.com, which sells balls up to 30 inches (0.75 meters) in diameter! A 16 inch (40 cm) ball is under $100 USD. 47 of 451
Page 1 and 2: Imatest Documentation © 2009 Imate
Page 3 and 4: Imatest Documentation Using SFRplus
Page 5 and 6: Imatest Documentation Image Quality
Page 7 and 8: Imatest Documentation tilted (about
Page 9 and 10: Imatest Documentation MTF50 in Line
Page 11 and 12: Imatest Documentation SQF Subjectiv
Page 13 and 14: Imatest Documentation RAW converter
Page 15 and 16: Imatest Documentation cm (4 inch) h
Page 17 and 18: Imatest Documentation CSF( f ) = 2.
Page 19 and 20: Imatest Documentation correlate wit
Page 21 and 22: Imatest Documentation Unlike the ab
Page 23 and 24: Imatest Documentation Since luminan
Page 25 and 26: Imatest Documentation committee" (I
Page 27 and 28: Imatest Documentation The formula f
Page 29 and 30: Imatest Documentation The image to
Page 31 and 32: Imatest Documentation Sharpness com
Page 33 and 34: Imatest Documentation (DPR) Canon E
Page 35 and 36: Imatest Documentation but their noi
Page 37 and 38: Imatest Documentation The average t
Page 39 and 40: Imatest Documentation Chromatic abe
Page 41 and 42: Imatest Documentation Veiling glare
Page 43 and 44: Imatest Documentation A Kodak Q-13
Page 45: Imatest Documentation with UV filte
Page 49 and 50: Imatest Documentation P_Rm = O_Rm*A
Page 51 and 52: Imatest Documentation Split view, s
Page 53 and 54: Imatest Documentation ISO Sensitivi
Page 55 and 56: Imatest Documentation Multicharts T
Page 57 and 58: Imatest Documentation Shoulders are
Page 59 and 60: Imatest Documentation Related docum
Page 61 and 62: Imatest Documentation between image
Page 63 and 64: Imatest Documentation We display va
Page 65 and 66: Imatest Documentation Blur units, M
Page 67 and 68: Imatest Documentation σ 2 = Σ (ti
Page 69 and 70: Imatest Documentation Drill holes l
Page 71 and 72: Imatest Documentation rummaging thr
Page 73 and 74: Imatest Documentation Target size C
Page 75 and 76: Imatest Documentation Level the tar
Page 77 and 78: Imatest Documentation Kodak Q-14 St
Page 79 and 80: Imatest Documentation Imatest Instr
Page 81 and 82: Imatest Documentation in the Imates
Page 83 and 84: Imatest Documentation samples (fold
Page 85 and 86: Imatest Documentation Using Imatest
Page 87 and 88: Imatest Documentation About RAW fil
Page 89 and 90: Imatest Documentation Options I for
Page 91 and 92: Imatest Documentation Special user
Page 93 and 94: Imatest Documentation CSV files- Ex
Page 95 and 96: Imatest Documentation RAW files RAW
Page 97 and 98:
Imatest Documentation dcraw The ori
Page 99 and 100:
Imatest Documentation The Rawview w
Page 101 and 102:
Imatest Documentation identical (th
Page 103 and 104:
Imatest Documentation The Imatest T
Page 105 and 106:
Imatest Documentation Tripod and ac
Page 107 and 108:
Imatest Documentation Targets Chart
Page 109 and 110:
Imatest Documentation Left of cente
Page 111 and 112:
Imatest Documentation Rope trick (f
Page 113 and 114:
Imatest Documentation Distortion ta
Page 115 and 116:
Imatest Documentation If you fail t
Page 117 and 118:
Imatest Documentation Diagnostics r
Page 119 and 120:
Imatest Documentation A horizontal
Page 121 and 122:
Imatest Documentation the edges pri
Page 123 and 124:
Imatest Documentation The camera mu
Page 125 and 126:
Imatest Documentation Epson 2200 Pr
Page 127 and 128:
Imatest Documentation Using SFR Par
Page 129 and 130:
Imatest Documentation ROI fine adju
Page 131 and 132:
Imatest Documentation Pixel size ha
Page 133 and 134:
Imatest Documentation contrast in h
Page 135 and 136:
Imatest Documentation Two precautio
Page 137 and 138:
Imatest Documentation The PNG files
Page 139 and 140:
Imatest Documentation nroi = 9 nwid
Page 141 and 142:
Imatest Documentation An optional .
Page 143 and 144:
Imatest Documentation SFR results:
Page 145 and 146:
Imatest Documentation Right column
Page 147 and 148:
Imatest Documentation Right: Input
Page 149 and 150:
Imatest Documentation Below the plo
Page 151 and 152:
Imatest Documentation Multi-ROI 2D
Page 153 and 154:
Imatest Documentation The Legend at
Page 155 and 156:
Imatest Documentation MTF50 (Cy/Pxl
Page 157 and 158:
Imatest Documentation Summary plot
Page 159 and 160:
Imatest Documentation 3D Plot for M
Page 161 and 162:
Imatest Documentation The standard
Page 163 and 164:
Imatest Documentation degrees are i
Page 165 and 166:
Imatest Documentation Using SFRplus
Page 167 and 168:
Imatest Documentation SFRplus setup
Page 169 and 170:
Imatest Documentation SFRplus setti
Page 171 and 172:
Imatest Documentation Gamma Gamma i
Page 173 and 174:
Imatest Documentation Using SFRplus
Page 175 and 176:
Imatest Documentation Weighted MTF5
Page 177 and 178:
Imatest Documentation This display
Page 179 and 180:
Imatest Documentation space of the
Page 181 and 182:
Imatest Documentation window, shown
Page 183 and 184:
Imatest Documentation It's easy to
Page 185 and 186:
Imatest Documentation Using Reschar
Page 187 and 188:
Imatest Documentation Select an ima
Page 189 and 190:
Imatest Documentation MTF contours
Page 191 and 192:
Imatest Documentation SFRplus SFR H
Page 193 and 194:
Imatest Documentation Log F-Contras
Page 195 and 196:
Imatest Documentation Log Frequency
Page 197 and 198:
Imatest Documentation Color moiré
Page 199 and 200:
Imatest Documentation The display o
Page 201 and 202:
Imatest Documentation phase) is twi
Page 203 and 204:
Imatest Documentation Downloadable
Page 205 and 206:
Imatest Documentation If Express mo
Page 207 and 208:
Imatest Documentation The display o
Page 209 and 210:
Imatest Documentation The differenc
Page 211 and 212:
Imatest Documentation Star Chart An
Page 213 and 214:
Imatest Documentation ROI fine adju
Page 215 and 216:
Imatest Documentation MTF (linear f
Page 217 and 218:
Imatest Documentation The plot on t
Page 219 and 220:
Imatest Documentation MTF Compare C
Page 221 and 222:
Imatest Documentation MTF Compare r
Page 223 and 224:
Imatest Documentation Comparison of
Page 225 and 226:
Imatest Documentation Batchview Pos
Page 227 and 228:
Imatest Documentation Rescharts SFR
Page 229 and 230:
Imatest Documentation Running Batch
Page 231 and 232:
Imatest Documentation Center mean O
Page 233 and 234:
Imatest Documentation standard mono
Page 235 and 236:
Imatest Documentation Lighting Inte
Page 237 and 238:
Imatest Documentation Run Imatest S
Page 239 and 240:
Imatest Documentation SFRplus setup
Page 241 and 242:
Imatest Documentation SFRplus setti
Page 243 and 244:
Imatest Documentation Additional pa
Page 245 and 246:
Imatest Documentation Output files
Page 247 and 248:
Imatest Documentation Lens-style MT
Page 249 and 250:
Imatest Documentation File formats
Page 251 and 252:
Imatest Documentation Purchase or d
Page 253 and 254:
Imatest Documentation Sharpness tar
Page 255 and 256:
Imatest Documentation Proper exposu
Page 257 and 258:
Imatest Documentation If you answer
Page 259 and 260:
Imatest Documentation SFR input dia
Page 261 and 262:
Imatest Documentation Figures (.PNG
Page 263 and 264:
Imatest Documentation contrast imag
Page 265 and 266:
Imatest Documentation Chromatic Abe
Page 267 and 268:
Imatest Documentation QA-61 ISO-160
Page 269 and 270:
Imatest Documentation Stepchart inp
Page 271 and 272:
Imatest Documentation First Figure:
Page 273 and 274:
Imatest Documentation Third Figure:
Page 275 and 276:
Imatest Documentation A camera's (o
Page 277 and 278:
Imatest Documentation The total dyn
Page 279 and 280:
Imatest Documentation Gamc is typic
Page 281 and 282:
Imatest Documentation ISO-15739 Noi
Page 283 and 284:
Imatest Documentation You can enter
Page 285 and 286:
Imatest Documentation Results If RA
Page 287 and 288:
Imatest Documentation Dynamic range
Page 289 and 290:
Imatest Documentation Using Colorch
Page 291 and 292:
Imatest Documentation horizontal fi
Page 293 and 294:
Imatest Documentation Colorcheck in
Page 295 and 296:
Imatest Documentation The first fig
Page 297 and 298:
Imatest Documentation The backgroun
Page 299 and 300:
Imatest Documentation saturated gre
Page 301 and 302:
Imatest Documentation (blank line)
Page 303 and 304:
Imatest Documentation CMC An early
Page 305 and 306:
Imatest Documentation The the equat
Page 307 and 308:
Imatest Documentation Multicharts o
Page 309 and 310:
Imatest Documentation If you select
Page 311 and 312:
Imatest Documentation The Zoom chec
Page 313 and 314:
Imatest Documentation + b* Pseudoco
Page 315 and 316:
Imatest Documentation Shows the gra
Page 317 and 318:
Imatest Documentation Multicharts S
Page 319 and 320:
Imatest Documentation Read from a 5
Page 321 and 322:
Imatest Documentation Use these ord
Page 323 and 324:
Imatest Documentation Color correct
Page 325 and 326:
Imatest Documentation Options: Colo
Page 327 and 328:
Imatest Documentation Exif and Colo
Page 329 and 330:
Imatest Documentation The Labsphere
Page 331 and 332:
Imatest Documentation Scaling butto
Page 333 and 334:
Imatest Documentation F-stop contou
Page 335 and 336:
Imatest Documentation Uniformity (L
Page 337 and 338:
Imatest Documentation density— vi
Page 339 and 340:
Imatest Documentation the Corner an
Page 341 and 342:
Imatest Documentation The local noi
Page 343 and 344:
Imatest Documentation Local nonunif
Page 345 and 346:
Imatest Documentation Image with sp
Page 347 and 348:
Imatest Documentation Using Distort
Page 349 and 350:
Imatest Documentation Set exposure
Page 351 and 352:
Imatest Documentation Plot distorti
Page 353 and 354:
Imatest Documentation Imatest will
Page 355 and 356:
Imatest Documentation MTF (sharpnes
Page 357 and 358:
Imatest Documentation Intersection
Page 359 and 360:
Imatest Documentation function of r
Page 361 and 362:
Imatest Documentation Imatest Instr
Page 363 and 364:
Imatest Documentation Horizontal di
Page 365 and 366:
Imatest Documentation Zone plates (
Page 367 and 368:
Imatest Documentation Along with ch
Page 369 and 370:
Imatest Documentation Preview image
Page 371 and 372:
Imatest Documentation Light Falloff
Page 373 and 374:
Imatest Documentation Monitor Calib
Page 375 and 376:
Imatest Documentation Black level (
Page 377 and 378:
Imatest Documentation Reset pattern
Page 379 and 380:
Imatest Documentation SVG Test Char
Page 381 and 382:
Imatest Documentation SVG SFR chart
Page 383 and 384:
Imatest Documentation To run Test C
Page 385 and 386:
Imatest Documentation Invert light/
Page 387 and 388:
Imatest Documentation Contrast (alt
Page 389 and 390:
Imatest Documentation window. Print
Page 391 and 392:
Imatest Documentation files. Quick
Page 393 and 394:
Imatest Documentation File selectio
Page 395 and 396:
Imatest Documentation Imatest IT/EX
Page 397 and 398:
Imatest Documentation cyclesper_val
Page 399 and 400:
Imatest Documentation optional. The
Page 401 and 402:
Imatest Documentation Change to the
Page 403 and 404:
Imatest Documentation Detailed inst
Page 405 and 406:
Imatest Documentation Scanner profi
Page 407 and 408:
Imatest Documentation Although this
Page 409 and 410:
Imatest Documentation Gamut is exce
Page 411 and 412:
Imatest Documentation S=1 HSL Hue p
Page 413 and 414:
Imatest Documentation An additional
Page 415 and 416:
Imatest Documentation Instructions
Page 417 and 418:
Imatest Documentation 7. 8. Mask im
Page 419 and 420:
Imatest Documentation 9. Corr Image
Page 421 and 422:
Imatest Documentation Appendix Cros
Page 423 and 424:
Imatest Documentation Sorted by tes
Page 425 and 426:
Imatest Documentation Distortion Un
Page 427 and 428:
Imatest Documentation Create Scalab
Page 429 and 430:
Imatest Documentation f-stop . Gamm
Page 431 and 432:
Imatest Documentation Glosario en E
Page 433 and 434:
Imatest Documentation Troubleshooti
Page 435 and 436:
Imatest Documentation You can selec
Page 437 and 438:
Imatest Documentation Imatest Chang
Page 439 and 440:
Imatest Documentation below, next t
Page 441 and 442:
Imatest Documentation Jan. 6, 2007
Page 443 and 444:
Imatest Documentation Nov. 6, 2005
Page 445 and 446:
Imatest Documentation Sept. 11, 200
Page 447 and 448:
Imatest Documentation XML Changes N
Page 449 and 450:
Imatest Documentation License The I
Page 451:
Imatest Documentation 11. GENERAL T
show all

Imatest Documentation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?