TXF_UserManual

Recommendations

Info

The description of different options in the NO CYCLE IS SELECTED screen is given as follow: OPERATIONS: Move to the OPERATIONS screen and perform different operations viz. DIAGNOSTICS, GLUE CYCLE, and WASH CYCLE. PREPARE TO PRINT: Move to the PREPARE TO PRINT screen to make the Conveyor Belt system “Online”. Operations When you select the OPERATIONS icon on the HMI, the OPERATIONS screen appears as shown below: Fig 6: Displaying the OPERATIONS Screen The description of different options in the OPERATIONS screen is given as follow: DIAGONSTICS: Move to the SERVICE MODE screen. GLUE CYCLE: Move to the GLUE CYCLE screen to start the glue coating and removing process. WASH CYCLE: Move to the WASH CYCLE screen to wash the Conveyor Belt. Icon: Go back to the previous screen. <strong>TXF</strong> Page | 12
Service Mode To open the SERVICE MODE screen, select the DIAGONSTICS icon from the OPERATIONS screen (Refer to Fig 6). The SERVICE MODE screen is shown as below: Fig 7: Displaying the SERVICE MODE Screen The description of different options in the SERVICE MODE screen is given as follow: BELT: Move the belt manually. TUB: Move the washing Tub Up, Down, and maintenance. BELT DRYER FAN: Switch ON or OFF the BELT DRYER FAN. TAKEUP: Run the fabric Take Up motor manually. IR DRYER FAN: Switch ON or OFF the IR DRYER FAN. <strong>TXF</strong> Page | 13
Page 1: USER MANUAL India’s largest manuf
Page 4 and 5: Table of Contents 1. About Document
Page 6 and 7: Monthly Maintenance ...............
Page 8 and 9: 2. Printer Overview The Front View
Page 10 and 11: 3. Control Panel (Print Engine) The
Page 12 and 13: Language Menu The Language Menu and
Page 16 and 17: Controlling Belt Motion To control
Page 18 and 19: Using the TAKE UP MOTION screen, yo
Page 20 and 21: Controlling Heaters Settings To cha
Page 22 and 23: 5. Before Use Preparation Before St
Page 24 and 25: Step 10: Set the starting position
Page 26 and 27: Step 3: Run the Wash Cycle from HMI
Page 28 and 29: Step 3: Go to the back of the machi
Page 30 and 31: Step 9: Once the glue seems to be d
Page 32 and 33: Step 4: Wait 5 minutes to dissolve
Page 34 and 35: Step 3: Fix the takeup roller by fo
Page 36 and 37: 6. Printing Check Ink Level Check t
Page 38 and 39: Performing Normal Cleaning Follow t
Page 40 and 41: Step 3: Press the Right arrow butto
Page 42 and 43: Printer Calibration Feed Calibratio
Page 44 and 45: Bidirectional Calibration Bi-direct
Page 46 and 47: Issuing Printing Command With TXF,
Page 48 and 49: Step 9: Turn OFF the power switch a
Page 50 and 51: Loading the Previously Saved Settin
Page 52 and 53: 8. Enabling the Sleep Mode This mac
Page 54 and 55: Step 2: Press the MENU button from
Page 56 and 57: Enabling the Manual Cleaning Mode F
Page 58 and 59: Step 4: Clean both wipers one by on
Page 60 and 61: Step 9: Start the cleaning the area
Page 62 and 63: Case-I: Belt Shifted Towards Left C
Page 64 and 65:
Precautions: Tub should alway
Page 66 and 67:
9. Troubleshooting PRINTER NOT INIT
Page 69:
For Any Query Please Contact Us www
show all

TXF_UserManual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?