Sections

Anchor Base Poles
RSAH
Features
Shaft – One-piece extruded 6063 aluminum
alloy with a T6 temper. Circumferential satinbrushed
finish. The round, straight tube is
uniform in cross-section down the length
of the shaft.
Hinged Anchor Base – Cast from A356
aluminum alloy, the anchor base is heattreated
to a T6 temper. The shaft inserts
into the tilting section of the hinged base
and is joined together by continuous circumferential
welds at the outside top and
inside bottom. The tilting and anchored
Ordering Information: See page 494
(Note: Poles are available only in U.S.)
INSTALLATION NOTES:
Installation requires grout to be packed under base to ensure
full contact with foundation. Factory-supplied templates must
be used when setting anchor bolts. Lithonia Lighting will not
accept claim for incorrect anchorage placement due to failure
to use Lithonia Lighting factory templates.
Do not erect poles without having fixtures installed.
If poles are stored outside, all protective wrapping must be
removed immediately to prevent finish damage.
3 /4" Solid aluminum pivot rod
Two-piece castaluminum
cover
C
Tapped 3/8"-16 for
ground connector
498 Outdoor / PSG8
B
A
Round Straight Aluminum, Hinged
sections of the hinged base are joined by
a ¾" diameter solid aluminum pivot rod. The
tilting section of the hinged base is held in
a vertical position by three ½"-13 x 2½"
stainless steel hex head bolts that attach
to stainless steel inserts cast into the aluminum
base. A cast-aluminum two-piece
cover is included.
Anchor Bolts – Top 12" galvanized per
ASTM A-153. Made of carbon steel bar
having a minimum-yield strength of
55,000 PSI.
Hand hole – Available as an option, and
located 90o to the right of the hinge.
Technical Information
EPA (ft 2 ) with 1.3 gust
Hardware – Stainless steel.
Top Cap – Cast-aluminum cap is provided
for drill-mount poles.
Finish – Standard finish is brushed aluminum.
Optional polyester powder painted and
anodized finishes available.
Nom. Pole Wall Bolt Bolt Approx.
Catalog mount. shaft size thick. 80 90 100 Max. circle size ship wt.
number ht. (ft.) (in. x in. x ft.) (in.) mph mph mph wt. (in.) (in. x in. x in.) (lbs)
RSAH 10 4C 10 4 x 4 x 10 0.125 8.2 6.1 4.7 100 8-1/2-10 3/4 x 18 x 3 43
RSAH 14 4C 14 4 x 4 x 14 0.125 4.4 3.0 2.1 100 8-1/2-10 3/4 x 18 x 3 50
RSAH 14 5E 14 5 x 5 x 14 0.156 10.6 8.2 6.5 100 8-1/2-10 3/4 x 18 x 3 66
RSAH 16 4C 16 4 x 4 x 16 0.125 3.1 1.9 1.2 100 8-1/2-10 3/4 x 18 x 3 54
RSAH 16 5C 16 5 x 5 x 16 0.125 6.2 4.7 3.6 100 8-1/2-10 3/4 x 18 x 3 60
RSAH 16 6E 16 6 x 6 x 16 0.156 13.8 10.7 8.5 100 8-1/2-10 3/4 x 30 x 3 88
RSAH 18 5C 18 5 x 5 x 18 0.125 4.5 3.3 2.5 130 8-1/2-10 3/4 x 18 x 3 65
RSAH 18 5G 18 5 x 5 x 18 0.188 8.2 6.2 4.9 130 8-1/2-10 3/4 x 18 x 3 90
RSAH 20 5C 20 5 x 5 x 20 0.125 3.2 2.2 1.6 130 8-1/2-10 3/4 x 18 x 3 69
RSAH 20 5G 20 5 x 5 x 20 0.188 6.4 4.8 3.7 130 8-1/2-10 3/4 x 18 x 3 97
RSAH 20 6G 20 6 x 6 x 20 0.188 11.7 9.0 7.1 130 8-1/2-10 3/4 x 30 x 3 110
Pole Data
Shaft Bolt Bolt Base Anchor Warehouse
base circle projection square bolt anchor bolt Template
size A B C description description number
4" 81/2"–10" 31/2" 125/8" ABRSAH-4 AB18-0 PJ50060
5" 81/2"–10" 31/2" 125/8" ABRSAH-5 AB18-0 PJ50061
6" 81/2"–10" 31/2" 125/8" ABRSAH-6 AB30-0 PJ50062
NOTES:
1 Mounting arrangement: (PT) Open Top; (T20) 2 3 /8" OD (2"
NPS)
2 Drill mounting: (DM19) 1 fixture at 90°; (DM28) 2 fixtures
at 180°
3 Options: See page 509.
4 Brackets: See page 511.
www.lithonia.com
keyword: RSAH