- Page 1 and 2:
SINGLE PULL MACGREGOR TYPE HATCH CO
- Page 3 and 4:
ACKNOWLEDGEMENT First of all we hel
- Page 5 and 6:
TABLE OF CONTENTS v Page no. CERTIF
- Page 7 and 8:
5.1.4 Hatch Covers Design. 58 5.1.5
- Page 9 and 10:
LIST OF FIGURES Figure no: Title Pa
- Page 11 and 12:
Figure7.10 Bulwark 84 Figure7.11 Bu
- Page 13 and 14:
CHAPTER 1 - INTRODUCTION The classi
- Page 15 and 16:
leakage can cause cargo damage and,
- Page 17 and 18:
All types of wooden hatch were made
- Page 19 and 20:
The first horizontal rolling built
- Page 21 and 22:
CHAPTER 2 - TYPES OF HATCH COVERS M
- Page 23 and 24:
2.1 SINGLE PULL 2.1.1 Description F
- Page 25 and 26:
2.3 FOLDING & MULTI-TYPE 2.3.1 Desc
- Page 27 and 28:
2.5 PIGGY BACK 2.5.1 Description Fi
- Page 29 and 30:
2.7 REEFERS HATCH COVERS Figure 2.7
- Page 31 and 32:
CHAPTER 3 - GENERAL REQUIREMENTS 3.
- Page 33 and 34:
secured by tarpaulins and battening
- Page 35 and 36:
force by the 1967 Merchant shipping
- Page 37 and 38:
3.2.2 Cover Stowage Where a designe
- Page 39 and 40:
It is also necessary to provide dra
- Page 41 and 42:
Other steel hatch cover secured wea
- Page 43 and 44:
Table 3.4 Access equipment strength
- Page 45 and 46:
Longitudinal deformation of the top
- Page 47 and 48:
(vii) It should retain all the abov
- Page 49 and 50:
easier to handle without power assi
- Page 51 and 52:
� Keep wheels, cleats, hinge pins
- Page 53 and 54: 4.2.2 Drive Chains; Check their Len
- Page 55 and 56: Figure 4.2 Vessel in rough weather
- Page 57 and 58: Figure 4.5 Never smoke in a hold. S
- Page 59 and 60: Figure 4.9 Always wear protective h
- Page 61 and 62: e taken when opening hatch covers e
- Page 63 and 64: Remember to carry out a chalk test
- Page 65 and 66: 4.6.13 Painting Corrosion occurs ma
- Page 67 and 68: 11. Coaming. 12. Sheave. 13. Cross
- Page 69 and 70: Breadth: 44.5cm 5.1.3 Hatch Coaming
- Page 71 and 72: Slope: 1cm Total number of panels:
- Page 73 and 74: Height of jack while normal conditi
- Page 75 and 76: Pulley for rope Diameter: 2cm Width
- Page 77 and 78: Height from the deck: 7.2cm Height
- Page 79 and 80: CHAPTER 6 - FABRICATION The design
- Page 81 and 82: 6.3 HATCH COAMING FABRICATION Broug
- Page 83 and 84: Using wood cutter length of 320 cm
- Page 85 and 86: Plastic wheels (16 pieces), metalli
- Page 87 and 88: At the top of the iron plate, rail
- Page 89 and 90: Figure 6.12: Crane space Source: Te
- Page 91 and 92: CHAPTER 7-ASSEMBLY OF FABRICATED PA
- Page 93 and 94: Source: Team 7.3 ASSEMBLY OF SIDE D
- Page 95 and 96: 7.6 ASSEMBLY OF HATCH COVER All the
- Page 97 and 98: The whole bulwark is placed over th
- Page 99 and 100: Through the middle top eye bolt rop
- Page 101 and 102: The test involves placing (with hat
- Page 103: CHAPTER 9 - CONCLUSION Right from t