Single pull macgregor type hatch cover.pdf - Cochin University of ...

More documents

Recommendations

Info

HOLD NO 4 : 37.5 × 30 × 16 HATCH OPENINGS IN METER : 18.65 × 11 NO OF PANTOONS : 4 TYPE : SINGLE PULL MACGREGOR TYPE NOTE : SACK CARRIER 5.1 PARTS DESIGN After studying all the hatch covers and their safety and operational aspects, team which comprise of six persons decided to design a working model of a single pull MacGregor type hatch cover. The various design aspects are given in this chapter. 5.1.1 Hold Design The hold design was selected from the cargo hold no 1 of the M V IRAN ship. The model was made in a convenient ratio 1: 25. Length of the hold: 150cm Width of the hold: 120cm Depth of the hold: 63.3cm Plate thickness: 1.5cm 5.1.2 Hatch Opening Dimensions Figure 5.2: Hold Design Source: Team The hatch opening dimension was exactly followed from cargo hold no 1. Length: 74.6cm 56
Breadth: 44.5cm 5.1.3 Hatch Coaming Design Figure 5.3: Hatch Opening Dimensions Source: Team The hatch coaming design is made from the ship after looking the minimum requirements stated in the load line convention. Height: 10.3cm Height of hatch coaming stay: 8.3 Width of hatch coaming stay: 2cm Thickness of hatch coaming stay: 1cm Supported area: 14.3cm Figure 5.4: Hatch Coaming Design Source: Team 57
Page 1 and 2:
SINGLE PULL MACGREGOR TYPE HATCH CO
Page 3 and 4:
ACKNOWLEDGEMENT First of all we hel
Page 5 and 6:
TABLE OF CONTENTS v Page no. CERTIF
Page 7 and 8:
5.1.4 Hatch Covers Design. 58 5.1.5
Page 9 and 10:
LIST OF FIGURES Figure no: Title Pa
Page 11 and 12:
Figure7.10 Bulwark 84 Figure7.11 Bu
Page 13 and 14:
CHAPTER 1 - INTRODUCTION The classi
Page 15 and 16:
leakage can cause cargo damage and,
Page 17 and 18: All types of wooden hatch were made
Page 19 and 20: The first horizontal rolling built
Page 21 and 22: CHAPTER 2 - TYPES OF HATCH COVERS M
Page 23 and 24: 2.1 SINGLE PULL 2.1.1 Description F
Page 25 and 26: 2.3 FOLDING & MULTI-TYPE 2.3.1 Desc
Page 27 and 28: 2.5 PIGGY BACK 2.5.1 Description Fi
Page 29 and 30: 2.7 REEFERS HATCH COVERS Figure 2.7
Page 31 and 32: CHAPTER 3 - GENERAL REQUIREMENTS 3.
Page 33 and 34: secured by tarpaulins and battening
Page 35 and 36: force by the 1967 Merchant shipping
Page 37 and 38: 3.2.2 Cover Stowage Where a designe
Page 39 and 40: It is also necessary to provide dra
Page 41 and 42: Other steel hatch cover secured wea
Page 43 and 44: Table 3.4 Access equipment strength
Page 45 and 46: Longitudinal deformation of the top
Page 47 and 48: (vii) It should retain all the abov
Page 49 and 50: easier to handle without power assi
Page 51 and 52: � Keep wheels, cleats, hinge pins
Page 53 and 54: 4.2.2 Drive Chains; Check their Len
Page 55 and 56: Figure 4.2 Vessel in rough weather
Page 57 and 58: Figure 4.5 Never smoke in a hold. S
Page 59 and 60: Figure 4.9 Always wear protective h
Page 61 and 62: e taken when opening hatch covers e
Page 63 and 64: Remember to carry out a chalk test
Page 65 and 66: 4.6.13 Painting Corrosion occurs ma
Page 67: 11. Coaming. 12. Sheave. 13. Cross
Page 71 and 72: Slope: 1cm Total number of panels:
Page 73 and 74: Height of jack while normal conditi
Page 75 and 76: Pulley for rope Diameter: 2cm Width
Page 77 and 78: Height from the deck: 7.2cm Height
Page 79 and 80: CHAPTER 6 - FABRICATION The design
Page 81 and 82: 6.3 HATCH COAMING FABRICATION Broug
Page 83 and 84: Using wood cutter length of 320 cm
Page 85 and 86: Plastic wheels (16 pieces), metalli
Page 87 and 88: At the top of the iron plate, rail
Page 89 and 90: Figure 6.12: Crane space Source: Te
Page 91 and 92: CHAPTER 7-ASSEMBLY OF FABRICATED PA
Page 93 and 94: Source: Team 7.3 ASSEMBLY OF SIDE D
Page 95 and 96: 7.6 ASSEMBLY OF HATCH COVER All the
Page 97 and 98: The whole bulwark is placed over th
Page 99 and 100: Through the middle top eye bolt rop
Page 101 and 102: The test involves placing (with hat
Page 103 and 104: CHAPTER 9 - CONCLUSION Right from t
show all

Single pull macgregor type hatch cover.pdf - Cochin University of ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?