Single pull macgregor type hatch cover.pdf - Cochin University of ...

More documents

Recommendations

Info

150 cm×120 cm (weather deck plate) 150 cm×120 cm (bottom plate) Marked dimensions were cut accordingly. These parts were joined together in the shape of cuboid with the help of nail and gum. Sander machine was used to get the surface finish. The final hold dimensions: 150 cm×120 cm×63.3 cm 6.2 FABRICATION OF HATCH WAY Hold space was marked and removed using wood cutter from the cuboid made above. The dimensions were: 74.6 cm along the longitudinal axis of the hold. 44.5 cm vertical to the longitudinal axis. Edges were well polished with sander machine. Figure 6.2: Hatch Way Source: Team 68
6.3 HATCH COAMING FABRICATION Brought the wooden piece to the work table which having the dimensions: Length: 300cm Breadth: 12cm Thickness: 2.8cm Length of 300 cm was divided into four parts as follows: 80cm: Two piece 50cm: Two piece All the four pieces were planed and polished. New dimensions of pieces were: Length: 80cm Length: 50cm Breadth: 11.8 cm Breadth: 11.8cm Thickness: 2.6 cm Thickness: 2.6cm All the four pieces were joined together with the help of nails and hatch coaming was made. Figure 6.3: Hatch Coaming Source: Team 69
Page 1 and 2:
SINGLE PULL MACGREGOR TYPE HATCH CO
Page 3 and 4:
ACKNOWLEDGEMENT First of all we hel
Page 5 and 6:
TABLE OF CONTENTS v Page no. CERTIF
Page 7 and 8:
5.1.4 Hatch Covers Design. 58 5.1.5
Page 9 and 10:
LIST OF FIGURES Figure no: Title Pa
Page 11 and 12:
Figure7.10 Bulwark 84 Figure7.11 Bu
Page 13 and 14:
CHAPTER 1 - INTRODUCTION The classi
Page 15 and 16:
leakage can cause cargo damage and,
Page 17 and 18:
All types of wooden hatch were made
Page 19 and 20:
The first horizontal rolling built
Page 21 and 22:
CHAPTER 2 - TYPES OF HATCH COVERS M
Page 23 and 24:
2.1 SINGLE PULL 2.1.1 Description F
Page 25 and 26:
2.3 FOLDING & MULTI-TYPE 2.3.1 Desc
Page 27 and 28:
2.5 PIGGY BACK 2.5.1 Description Fi
Page 29 and 30: 2.7 REEFERS HATCH COVERS Figure 2.7
Page 31 and 32: CHAPTER 3 - GENERAL REQUIREMENTS 3.
Page 33 and 34: secured by tarpaulins and battening
Page 35 and 36: force by the 1967 Merchant shipping
Page 37 and 38: 3.2.2 Cover Stowage Where a designe
Page 39 and 40: It is also necessary to provide dra
Page 41 and 42: Other steel hatch cover secured wea
Page 43 and 44: Table 3.4 Access equipment strength
Page 45 and 46: Longitudinal deformation of the top
Page 47 and 48: (vii) It should retain all the abov
Page 49 and 50: easier to handle without power assi
Page 51 and 52: � Keep wheels, cleats, hinge pins
Page 53 and 54: 4.2.2 Drive Chains; Check their Len
Page 55 and 56: Figure 4.2 Vessel in rough weather
Page 57 and 58: Figure 4.5 Never smoke in a hold. S
Page 59 and 60: Figure 4.9 Always wear protective h
Page 61 and 62: e taken when opening hatch covers e
Page 63 and 64: Remember to carry out a chalk test
Page 65 and 66: 4.6.13 Painting Corrosion occurs ma
Page 67 and 68: 11. Coaming. 12. Sheave. 13. Cross
Page 69 and 70: Breadth: 44.5cm 5.1.3 Hatch Coaming
Page 71 and 72: Slope: 1cm Total number of panels:
Page 73 and 74: Height of jack while normal conditi
Page 75 and 76: Pulley for rope Diameter: 2cm Width
Page 77 and 78: Height from the deck: 7.2cm Height
Page 79: CHAPTER 6 - FABRICATION The design
Page 83 and 84: Using wood cutter length of 320 cm
Page 85 and 86: Plastic wheels (16 pieces), metalli
Page 87 and 88: At the top of the iron plate, rail
Page 89 and 90: Figure 6.12: Crane space Source: Te
Page 91 and 92: CHAPTER 7-ASSEMBLY OF FABRICATED PA
Page 93 and 94: Source: Team 7.3 ASSEMBLY OF SIDE D
Page 95 and 96: 7.6 ASSEMBLY OF HATCH COVER All the
Page 97 and 98: The whole bulwark is placed over th
Page 99 and 100: Through the middle top eye bolt rop
Page 101 and 102: The test involves placing (with hat
Page 103 and 104: CHAPTER 9 - CONCLUSION Right from t
show all

Single pull macgregor type hatch cover.pdf - Cochin University of ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?