SERVICE MANUAL - SONYRUS
SERVICE MANUAL - SONYRUS
SERVICE MANUAL - SONYRUS
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
2-1. FLOW CHART<br />
The following flow chart shows the disassembly procedure.<br />
1 2<br />
3<br />
1 Ornamental ring (A)<br />
2 Tapping screw (M1.2) x2<br />
3 Barrier assy<br />
Note: When you exchange rings, be sure<br />
to follow the procedure carried on<br />
"2-3. Exchange Method of Barrier<br />
Assy" (2-5 page).<br />
1<br />
3<br />
SECTION 2<br />
DISASSEMBLY<br />
1 Lock ace screw (M1.7) x4<br />
2 Claw<br />
3 Rear cabinet<br />
4 Side cover<br />
5 Sheet (S)<br />
2<br />
4<br />
1<br />
HELP<br />
7<br />
6 Mic harness: CN102<br />
7 Lock ace screw (M1.7) x2<br />
8 Front cabinet<br />
8<br />
6<br />
5<br />
1<br />
2<br />
3<br />
2<br />
4<br />
6<br />
5<br />
9 qa<br />
8<br />
1 Claw x1 qs<br />
2 Claw x1<br />
3 Control SW block<br />
4 Control SW block flexible: CN702<br />
5 ST-101 flexible: CN601<br />
5<br />
4<br />
2-1 2-2<br />
0<br />
1<br />
1 BT terminal flexible: CN001<br />
2 Tapping screw (M1.7) x2<br />
3 SY-102<br />
4 MS-205 flexible: CN704<br />
5 Lock ace screw (M1.7) x2<br />
3<br />
7<br />
6<br />
0<br />
1<br />
0<br />
8<br />
9<br />
Note: High-voltage cautions<br />
Discharging the Capacitor<br />
Short-circuit between the two<br />
points with the short jig about 10<br />
seconds.<br />
ST-101<br />
9<br />
Capacitor<br />
R:1 kΩ/1 W<br />
(Part code:<br />
1-215-869-11)<br />
7<br />
6 Tapping screw (M1.7) x2<br />
7 Boss<br />
8 DC and A/V jack<br />
9 Claw x2<br />
0 MS-205<br />
ST kemikon sheet<br />
6 Claw x2<br />
7 Strobo block<br />
8 Tapping screw (M1.7) x1<br />
9 DC ground plate (B)<br />
0 Claw x2<br />
qa Claw x1<br />
qs Bottom cabinet<br />
8<br />
2<br />
4<br />
5<br />
1 3<br />
DSC-W1/W12<br />
HELP<br />
1 Open two connectors (CN201, 701)<br />
2 Claw x2<br />
3 Lens block<br />
4 CD-507: CN701<br />
5 Lens block flexible: CN201<br />
9<br />
6<br />
4<br />
1 Lock ace screw<br />
(M1.7) x2<br />
2 SW-422<br />
3 US-011 flexible: CN101<br />
4 Lock ace screw<br />
(M1.7) x1<br />
5 Claw x4<br />
1<br />
3<br />
0<br />
2<br />
2<br />
5<br />
5<br />
qa<br />
7<br />
6 US-011<br />
7 Claw x2<br />
8 Claw x2<br />
9 LCD block<br />
0 LCD flexible: CN801<br />
qa Back light<br />
flexible: CN802
Change language