38059-Satchwell Inter. Guide 05
38059-Satchwell Inter. Guide 05
38059-Satchwell Inter. Guide 05
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Pipe Temperature Sensors<br />
DST 0001<br />
Water Temp.<br />
Sensor (surface)<br />
DWT 0001<br />
Water Temperature<br />
Sensor<br />
(immersion)<br />
DWT 0002<br />
Fast Response<br />
Water Sensor<br />
(immersion)<br />
The DST 0001 permits the monitoring and control of fluid<br />
temperature through its specially designed thermistor<br />
housing. Its simple installation promotes its flexible use for<br />
temporary or permanent monitoring/control applications.<br />
FEATURES<br />
• Allows direct mounting to pipe surface, allowing any<br />
point to be monitored<br />
• Easily fitted, making it perfect for permanent or<br />
temporary situations<br />
• Simple commissioning<br />
This sensor simplifies product selection and improves control<br />
loop performance with its unique probe assembly. The shaft<br />
is simply extended and inserted into the pocket, ensuring a<br />
good contact. The sensor can be used with a vast range of<br />
other manufacturer’s pockets when used in conjunction with<br />
the pocket adaptor DWA 0001. The use of the adaptor<br />
avoids system drain downs and costly down time.<br />
FEATURES<br />
• Variable stem length - 100mm to 330mm<br />
• Sensor crown ensures good thermal contact with<br />
pocket end<br />
• Fast response<br />
• 120mm brass pocket (DWA 00<strong>05</strong>) and heat conductive<br />
paste supplied as standard<br />
• Simple commissioning<br />
The DWT 0002 sensor is designed for use in the most<br />
demanding control schemes. Many modern applications call<br />
for above average performance and this device is key to<br />
stability and efficiency. The sensing element is encased in the<br />
optimum amount of high quality stainless steel, permitting<br />
ultra fast detection of temperature change.<br />
FEATURES<br />
• Very fast response to temperature change<br />
• Small probe diameter for direct insertion into small pipes<br />
• Stainless steel probe<br />
• Simple commissioning<br />
PRODUCT SELECTION <strong>Satchwell</strong> Sensors<br />
Duct Temperature, Temperature/humidity, Carbon Dioxide & Pressure Sensors (cont)<br />
DDCO<br />
Infrared Analyser<br />
CO 2 Sensor<br />
DDV<br />
Air Velocity Sensor<br />
The DDCO is a non-dispersive infrared analyser designed for<br />
measuring environmental CO2 concentration in ventilation<br />
systems and indoor living spaces. Its measurement range of<br />
0...2000 or 0...5000 ppm covers the range required to<br />
monitor compliance with ASHRAE or other ventilation<br />
efficiency standards.<br />
An LCD display is available to provide local indication of CO2 concentration and facilitate the setup and calibration<br />
process. An adjustable setpoint relay is available for direct<br />
control and alarm applications. Microprocessor-based digital<br />
electronics and a unique self-calibration algorithm improves<br />
long-term stability and accuracy.<br />
The DDV gives a 0...5Vdc output over a range of 0.4...10 m/s.<br />
The velocity range may be limited if required to give greater<br />
resolution. On its minimum setting the range is<br />
approximately 0.4 to 4 m/s.<br />
24<br />
Measurement Repeatability Operating Input Analogue output<br />
range (selectable) temp. voltage (selectable)<br />
DDCO 2602 0...2000 or ±20 ppm 0...50°C 20...30V 0...5Vdc,<br />
0...5000 ppm ac/dc 0...10Vdc<br />
or 4...20mA<br />
Data Sheet 1.601<br />
Protection class - IP 65<br />
Accuracy - ±75 ppm<br />
Response time -