38059-Satchwell Inter. Guide 05

Temperature Controllers
Item/ Range Current Equipment Notes Remarks
Spec. no.
Intronic X
575-1-201 6...40°C ● ● Detectors/sensors
575-1-202 40...110°C ● to be replaced
Monotronic
574-2-551 6...40°C ● ● ●
574-2-552 20...95°C ●
574-2-553 45...125°C ●
Climatronic CXT
562-3-601 –5...40°C ● ● CXT 5605 can use
562-3-602 20...70°C ● existing sensors
562-3-603 35...120°C ●
562-3-604 35...120°C ●
562-4-601 0...50°C ●
562-4-604 30...120°C ●
Climatronic AXT Controller-motor
566-1-601 5...40°C ● ● Detectors/sensors
566-1-602 20...65°C ● to be changed if
566-1-603 35...120°C ● MMC, KMC is
566-1-651 5...40°C ● ● being installed
Climatronic AZT Controller-motor
566-1-301 –5...40°C ● ● ●
566-1-302 –5...40°C ● ● ●
566-1-303 35...120°C ●
566-1-351 –5...40°C ● ● ●
566-1-352 –5...40°C ● ● ●
Climatronic CZT
562-3-301 –5...40°C ● ● ● CZT 5305 can use
562-3-302 –5...40°C ● ● ● existing sensors
562-3-303 35...120°C ●
562-4-302 –5...40°C ●
562-4-303 30...120°C ●
CD ARE actuator +
567-2-401 ● linkage kit
Climatronic AZT Controller-motor
566-3-001 10...35°C ● ● Detectors/sensors
566-3-302 10...35°C ● ● to be changed if
566-3-304 10...35°C ● ● MMC, KMC is
566-3-352 10...35°C ● ● being installed.
566-3-354 10...35°C ● ●
Controller-actuator AET, AEST
568-1-201 10...40°C ● ● ● Detectors/sensors
568-1-202 10...40°C ● ● ● to be changed if
568-1-301 10...40°C ● ● ● adjustable type.
568-1-302 10...40°C ● ● ● Also if MMC, KMC
is installed.
Controller-motor AXR
566-1-801 ● ● Detectors/sensors
to be changed if
MMC being installed.
Climatronic CXR
562-1-801 ● ●
562-2-801 ● ● CXR 5805 can use
562-3-801 ● ● existing sensors
562-4-831 10...40°C ●
562-4-801 10...40°C ●
Monotronic Balancing Relay (ZC)
581-2-201 No equivalent
replacement
Climatronic AZS Controller-motor
485-1-201
Climatronic CZS
562-3-201
CXR 5805
CXT 5605
CZT 5305
KMC 3201
MMC 4701
Keyboard
CMT 1201 563-1-201 ● MMC 4701 can use
FMS 1201 583-1-201 ● existing sensors
MPD 1801 583-1-801 No equivalent
COE 1601 583-1-601 replacements
FSS 1001 583-1-001
FSS 1401 583-1-401
FSC 1251 583-1-251
Micro Management
MMC 2401 –40...140°C ●
MMC 2402 –40...140°C ●
MMC 2403 –40...140°C ●
MMC 2451 –40...150°C ●
MMC 2452 –40...150°C ●
MMC 2453 –40...150°C ●
MMC 3701 –40...150°C ●
Keyboard
KZT 4351 5...50°C
0...10Vdc
●
KET 4201 5...50°C
0...10Vdc
●
Product Selection - page no. 17 18 18 18 19
OBSOLETE PRODUCTS Satchwell Controllers & Detectors/Sensors
Actuators must be
replaced with a 0...10V
type when used with
CZT/KMC or
multi-stage MMC’s.
These controls are
controller/actuator
combined therefore a
replacement actuator
will be required.
Controller/actuator
combined therefore
actuator to be
replaced.
Controller/actuator
combined therefore
actuator to be
replaced.
Change system.
Refer to Satchwell or
contact your local
sales engineer.
38
Detectors/sensors
Current Equipment
DDH DDTH DRH DRTH
7XXX 7XXX 7XXX 7XXX
8XXX 8XXX 8XXX 8XXX
Adjustable scale none none none none
Location duct duct room room
Item Spec. no. Notes Remarks
Detectors
EH 331-1-401
ZHT 331-2-601 No direct
DDH 331-3-702
331-3-704
equivalent
available
DRH 331-3-601
331-3-602
DRH 331-3-401 ● Direct replacement
ABC = 123
DRH 331-4-401 ● Change terminal nos.
DRTH 331-7-501 ● Requires remounting
DRTH 7722
DRTH 7723
DDH 331-3-451 ●
DDH 331-7-451 ● Fixing is the same but enclosure size
DDTH 331-7-551 ● is slightly different.
DDH 331-3-551
DO 2202
DD 1401
DD 1403
DD 336-1-204 No direct
DW 1202
DW 1204
equivalent
available
DWS 339-1-304
DR 3251
DR 3252
DRT 215-1-601
DDE 331-3-301
DDTE 1601
DWTE 1201
DWTE 1202
Product Selection - page no. 23 23 22 22
Spec. no. Range Stem/pocket
Current Equipment
Item Spec. no. Range Notes Remarks
Regulator Thermostats
CR No equivalent
CRX
available
Outside Pilot No equivalent
CP available
Detectors
C7P 326-2-501 No equivalent
C7W 323-2-501
available
CO 327-1-202 No equivalent
available
ET 325-1-201
325-1-251
325-1-301
ZW 323-2-201 No equivalent
323-2-204
323-2-207
available
ZHO 331-2-701
EO 326-1-303
DP 334-1-201
Limiting Detectors
LO 137-1-452 5...60°C No equivalent
LR 167-1-253 20...90°C
available
LZS 315-1-201 10...40°C
Change complete
system to KMC
or MMC.
Actuators and
detectors/sensors to
be replaced.
If valve fitted check
suitable actuator
replacement.
DDH 3451 uses 15Vdc
power supply
DDTH 7551 requires
24Vac power supply.
Refer to Satchwell or
contact your local
sales engineer.
DDU DDT DWT DWT DST DOT DOS
1803 0001 0001 0002 0001 0002 0001
Adjustable scale none none none none none none none
Location duct duct imm. imm. clamp outs. outs.
DDT 1701 –5...+100°C 300mm ●
DDU 1801 –5...+40°C – ●
DWT 1701 –10...+120°C 125mm ● *
DWT 1702 –10...+120°C 200mm ● *
DWT 1801 –10...+120°C 165mm ●
DST 1601 5...120°C – ●
DOT 2301 –40...+40°C – ●
DOT 0001 –40...+55°C – ●
DOS 2501 – – ●
Product Selection - page no. 23 23 24 24 24 25 25
* note: DWA 0001 is required
Change complete
system to CSC with
detectors/sensors.
If actuator is XKM or
XPM then a
transformer must
be supplied.
Change complete system
to CSC or MMC with
detectors/sensors. If actuator
is XKM or XPM then a
transformer must be supplied.
Change control system
dependant upon
existing controls.
Refer to Satchwell with
full specification
number of obsolete
control and
temperature range of
controller or contact
your local sales
engineer.