The Official JungleFlasher User Guide

Recommendations

Info

Alternative option for those with PMT/Probe 3 - failed unlock or bad-flashed CLICK HERE MS25 Is The Firmware on drive STOCK? IF UNSURE – ASSUME NO! Click Here Xtreme 3.3 > iXtreme 1.4 CLICK HERE or Samsung What Version of drive? Page 14 of 223 Is The Firmware on drive STOCK? IF UNSURE – ASSUME NO! YES NO YES Hacked Firmware! Which Version? iXtreme 1.5> iXtreme 1.61 CLICK HERE Click Here Things not going as expected? – Read the FAQ’s or MS28 iXtreme LT CLICK HERE Alternative option for Nforce or Via chipset users. For ALL Samsung drives CLICK HERE IF – you ASSUMED MS28 drive did not have stock firmware BUT have no luck unlocking it, using these methods – try SAMMY UNLOCK BUTTON
Unlocking the drive. Before we can do anything to the drive, it must be in Vendor Mode (status 0x70). All Unlocking is taken place under the MTKFlash 32 tab. Note: Upon selecting the correct port the drive shows up and key is dumped and verified against the drive! (Before doing anything to the drive) – The firmware has NOT yet been dumped! However if you save the log you now have a known verified key from your drive. Please note, unmodified Samsung MS25’s have no FirmGuard therefore do not need an unlock method to be applied, simply click Intro / DeviceID and check flash chip properties for status 0x70. Page 15 of 223 Things not going as expected? – Read the FAQ’s
Page 1 and 2: JungleFlasher v0.1.82 (x86 and x64
Page 3 and 4: Introduction JungleFlasher is devel
Page 5 and 6: Benq too (though not automated like
Page 7 and 8: BEFORE USING JUNGLEFLASHER You Must
Page 9 and 10: WHEN you run Jungleflasher you MUST
Page 11 and 12: Samsung CLICK HERE BenQ CLICK HERE
Page 13: Samsung (TS-H943) MS25 /MS28. Overv
Page 17 and 18: Unlocking the drive. Before we can
Page 19 and 20: Stock MS28’s (Unmodified). Sammy
Page 21 and 22: Xtreme 3.3 -> iXtreme 1.4 Unlock us
Page 23 and 24: Unlocking iXtreme 1.5 > 1.61 For th
Page 25 and 26: DeviceID Unlock / Vcc Trick (VIA/Nf
Page 27 and 28: Alternate method if you are struggl
Page 29 and 30: Reading the Firmware from the drive
Page 31 and 32: To save a firmware file based on wh
Page 33 and 34: Ok, now you have flashed your Samsu
Page 35 and 36: Unlocking the drive. Before we can
Page 37 and 38: BenQ UnLock Stock/ iXtreme 1.1 -> 1
Page 39 and 40: DeviceID Unlock / Vcc Trick (VIA/Nf
Page 41 and 42: CLICK HERE TO PROCEED If it didn’
Page 43 and 44: While ……. are appearing, Turn O
Page 45 and 46: Click Yes to auto load iXtreme (fro
Page 47 and 48: Write Command, will send Chip Erase
Page 49 and 50: Regardless of option chosen, the Hi
Page 51 and 52: Setting ModeB Connect your Hitachi
Page 53 and 54: The drive should now report as in M
Page 55 and 56: JungleUSB Drivers and USmodeB (XP O
Page 57 and 58: Click Have Disk Now click Browse an
Page 59 and 60: If all went well you should now hav
Page 61 and 62: Dumping the Firmware from the drive
Page 63 and 64: Once firmware is read, JungleFlashe
Page 65 and 66:
The Drive is now unlocked! UNLOCKED
Page 67 and 68:
JungleFlasher will now dump the dri
Page 69 and 70:
Then, click Flash LT Plus JungleFla
Page 71 and 72:
Power Off - Disconnect drive, conne
Page 73 and 74:
JungleFlasher will dump the Hacked
Page 75 and 76:
Spoofing a Hitachi Drive to report
Page 77 and 78:
JungleFlasher will then read, compa
Page 79 and 80:
Auto Spoofing a Hitachi As with all
Page 81 and 82:
Power Off - Disconnect drive, conne
Page 83 and 84:
Possibly Stock 83850C v1? CLICK HER
Page 85 and 86:
Lite-On PLDS DG-16D2S(-09C) - Legac
Page 87 and 88:
IF you have previously flashed this
Page 89 and 90:
Then, pull the tray out fully and p
Page 91 and 92:
Note: If you wish to include calibr
Page 93 and 94:
Then, simply click Dummy from iXtre
Page 95 and 96:
optionally, choose to dump dummy.bi
Page 97 and 98:
Using USB Cable to connect (can als
Page 99 and 100:
There is now No Requirement to dump
Page 101 and 102:
Check the OSIG/models info match Ch
Page 103 and 104:
Erasing a Lite-On PLDS DG-16D2S. PL
Page 105 and 106:
Drive is now in Vendor Mode (0x72).
Page 107 and 108:
This will save you power cycling th
Page 109 and 110:
Select DVDKey32 Tab Check to see th
Page 111 and 112:
Here you must set the tray to ‘Ha
Page 113 and 114:
Jungleflasher will now prompt you t
Page 115 and 116:
Dumping OFW from LiteOn for 83850C
Page 117 and 118:
The MRA Hack Can be used on ALL cur
Page 119 and 120:
REFRESH BUTTON Turn power off to th
Page 121 and 122:
DO NOT POWER CYCLE! If everything h
Page 123 and 124:
Select Yes Now, Just follow the sta
Page 125 and 126:
Turn power to the drive off. Operat
Page 127 and 128:
Once you have the Correct status (s
Page 129 and 130:
Just follow the standard write proc
Page 131 and 132:
Now take the Xecuter Probe II and p
Page 133 and 134:
Turn the power OFF on the CK3. Push
Page 135 and 136:
Vampire Using Rebuild Board Install
Page 137 and 138:
In case you get STATUS 0x72 but the
Page 139 and 140:
Using Vampire if you are NOT USING
Page 141 and 142:
While you have the button on Vampir
Page 143 and 144:
Once you have soldered the jumper o
Page 145 and 146:
Check the running log to see all th
Page 147 and 148:
Is the Firmware in the same place o
Page 149 and 150:
It will open as source and auto loa
Page 151 and 152:
Using the KeyDatabase to Create you
Page 153 and 154:
Click Yes, Page 153 of 223 Things n
Page 155 and 156:
Removing VIA drivers (Windows XP/Vi
Page 157 and 158:
select Disable Acknowledge the warn
Page 159 and 160:
Manual Spoofing Hopefully the excel
Page 161 and 162:
USB Only, VIA Ports only & Include
Page 163 and 164:
The data required is located in 4 p
Page 165 and 166:
Spoofing as a different type of dri
Page 167 and 168:
Now click Spoof Source to Target! N
Page 169 and 170:
Advanced User Info Advanced Ctrl+Fk
Page 171 and 172:
Page 171 of 223 Things not going as
Page 173 and 174:
� Adview - Remembers whether Adva
Page 175 and 176:
3. Will create a dummy.bin from the
Page 177 and 178:
Using the PMT With drive powered on
Page 179 and 180:
Page 181 and 182:
Switch 3.3v inline switch ON again
Page 183 and 184:
From here the Jungleflasher procedu
Page 185 and 186:
Using the PMT With drive powered on
Page 187 and 188:
Page 189 and 190:
Switch Drive Power ON again This me
Page 191 and 192:
This will as normal take you to the
Page 193 and 194:
Then select Intro / Device ID butto
Page 195 and 196:
Samsung Drives Using PMT or CK Prob
Page 197 and 198:
Then power off your drive - you wil
Page 199 and 200:
LiteOn Slim FW Ver. 0225 Dumping th
Page 201 and 202:
(as shown below) Jungleflasher will
Page 203 and 204:
Now select Slim Unlock Jungleflashe
Page 205 and 206:
Now Jungleflasher will change to th
Page 207 and 208:
Write Firmware to the Slim 9504 Sel
Page 209 and 210:
Method B - Using SlimKey First sele
Page 211 and 212:
Please do so - having a saved copy
Page 213 and 214:
Common problems and Frequently Aske
Page 215 and 216:
JungleFlasher will only show drives
Page 217 and 218:
To overcome this, we can change one
Page 219 and 220:
In what sequence should I switch th
Page 221 and 222:
Additional Info for running JungleF
Page 223:
JungleFlasher v0.1.82 beta Thanks t
show all

The Official JungleFlasher User Guide

Create successful ePaper yourself

Delete template?

Save as template?