WebPAM User v1.5 - Promise Technology, Inc.

More documents

Recommendations

Info

WebPAM User Manual Click on the Logical Drive Icon to see all of the information about your new logical drive. Before you can use your new logical drive, you must partition and format the logical drive using your PC’s operating system. See “Appendix B: Partition and Format” on page 105 for more information. 26
Log-out of WebPAM There are two ways to log out of WebPAM: • Close your browser window • Click Logout on the WebPAM banner (below) 27 Chapter 3: Setup After logging out, you must enter your username and password to log in again. Clicking Logout brings you back to the Login Screen. Internet Connection using WebPAM The above instructions cover connections between the Host PC and other PCs using WebPAM over your company network. It is also possible to connect to a Host PC from the Internet. Your MIS Administrator can tell you how to access your network from outside the firewall. Once you are logged onto the network, you can access the Host PC using its IP address. Please note that only the Host PC with the FastTrak RAID Controller can read and write data to the logical drives. However, other PCs can monitor the Host PC from virtually any location. Run WebPAM without Network Connection While WebPAM was designed to run over a network, you can run WebPAM without a network connection but only from the Host PC. Follow this procedure: 1. Double-click the WebPAM desktop icon. Your browser opens and displays a “no connection to the Internet is currently available” message. 2. Click the Work Offline button. 3. In the WebPAM login screen, enter your user name and password (if used), then click the Sign in button. A “webpage unavailable while offline” message will display. 4. Click the Connect button. A “no connection to the Internet is currently available” message will display. 5. Click the Try Again button. After a few moments, WebPAM will display normally in your browser.
Page 1 and 2: WEBPAM USER MANUAL Version 1.5
Page 3 and 4: Contents Chapter 1: Introduction .
Page 5 and 6: v Contentsn Chapter 5: Monitor and
Page 7 and 8: Chapter 1: Introduction • WebPAM
Page 9 and 10: PAM Installation Options 3 Chapter
Page 11 and 12: About This Manual 5 Chapter 1: Intr
Page 13 and 14: Chapter 2: Installation • Utility
Page 15 and 16: Install WebPAM 9 Chapter 2: Install
Page 17 and 18: 11 Chapter 2: Installation 7. When
Page 23 and 24: Chapter 3: Setup • Log-in to WebP
Page 25 and 26: After sign-in, the WebPAM opening s
Page 27 and 28: 21 Chapter 3: Setup 4. If you want
Page 29 and 30: 23 Chapter 3: Setup 3. Select the r
Page 31: 25 Chapter 3: Setup 11. Select a St
Page 35 and 36: Chapter 4: WebPAM User Interface
Page 37 and 38: A Host PC’s RAID system is made u
Page 39 and 40: Event Frame 33 Chapter 4: WebPAM Us
Page 41 and 42: Chapter 5: Monitor and Manage • L
Page 43 and 44: User Management • Add a User (bel
Page 45 and 46: 39 Chapter 5: Monitor and Manage Th
Page 47 and 48: Delete a User 1. In Tree View, clic
Page 49 and 50: 43 Chapter 5: Monitor and Manage 1.
Page 51 and 52: Host Management 45 Chapter 5: Monit
Page 53 and 54: FastTrak 47 Chapter 5: Monitor and
Page 55 and 56: Controller Settings Click on the Se
Page 57 and 58: 4. Click the Delete button. 5. In t
Page 59 and 60: Split a Physical Drive 53 Chapter 5
Page 61 and 62: Media Patrol Schedule 55 Chapter 5:
Page 63 and 64: 57 Chapter 5: Monitor and Manage
Page 65 and 66: 3. Click on the Media Patrol tab in
Page 67 and 68: 4. Click the Locate Drive button. 6
Page 71 and 72: 65 Chapter 5: Monitor and Manage 11
Page 73 and 74: 67 Chapter 5: Monitor and Manage If
Page 75 and 76: 69 Chapter 5: Monitor and Manage
Page 77 and 78: 3. Click on the Migration tab in Ma
Page 79 and 80: Logical Drive Rebuild 73 Chapter 5:
Page 83 and 84:
77 Chapter 5: Monitor and Manage Lo
Page 85 and 86:
3. Click on the Synchronization tab
Page 87 and 88:
Identify the Failed Disk Drive 81 C
Page 89 and 90:
Enclosures Enclosure View 83 Chapte
Page 91 and 92:
Spare Drives 85 Chapter 5: Monitor
Page 93 and 94:
Delete a Spare Drive To delete a sp
Page 95 and 96:
Chapter 6: Technology Background
Page 97 and 98:
RAID 1 - Mirror 91 Chapter 6: Techn
Page 99 and 100:
RAID 10 - Mirror / Stripe 93 Chapte
Page 101 and 102:
Choosing a RAID Level 95 Chapter 6:
Page 103 and 104:
Choosing Stripe Block Size 97 Chapt
Page 105 and 106:
Cache Settings 99 Chapter 6: Techno
Page 107 and 108:
See the chart below. Current LD Siz
Page 109 and 110:
Appendix A: Frequently Asked Questi
Page 111 and 112:
Appendix B: Partition and Format In
Page 113 and 114:
107 Appendix A: Partition and Forma
show all

WebPAM User v1.5 - Promise Technology, Inc.

Create successful ePaper yourself

Delete template?

Save as template?