WebPAM User v1.5 - Promise Technology, Inc.

More documents

Recommendations

Info

<strong>WebPAM</strong> <strong>User</strong> Manual 3. From the Logical Drive dropdown menu, select • Global Spare – This Spare Drive can be used by any qualified Logical Drive. • Logical Drive – The name of the logical drive to which this Spare Drive will be assigned or dedicated. 4. Click on a disk drive to select it. Available drives have a black frame. Selected drives have a red frame. Drives with a blue frame are assigned to a logical drive. You cannot assign a split drive as a spare drive. 5. Click the Create button. The new Spare Drive appears under Physical Drive View and Spare Drive View. 86
Delete a Spare Drive To delete a spare drive: 1. Click on the Logical Drive View icon. 2. Select the Delete tab. 87 Chapter 5: Monitor and Manage 3. Check the box to the left of the spare drive you want to delete. 4. Click the Delete button. 5. In the Confirmation box, click the OK button. The selected spare drive is deleted. Battery The Information tab displays information about the cache-backup battery. To access the Controller–Information tab, click on the Battery icon in Tree View. • Temperature – The battery's operating temperature. The battery normally has the same temperature as the inside of the PC where it is installed, typically below 38°C or 100°F. If the battery temperature rises above this value, determine whether the PC is overheating. If the PC is OK but the battery is too hot, the battery is not accepting a charge properly and you must replace it. • Voltage – The battery supplies 3.3V to back up the controller cache in the event of a power failure. If battery voltage drops below this value, the battery is not accepting a charge properly and you must replace it. If the Battery icon does not appear in Tree View, the battery is either disconnected or was not installed.
Page 1 and 2:
WEBPAM USER MANUAL Version 1.5
Page 3 and 4:
Contents Chapter 1: Introduction .
Page 5 and 6:
v Contentsn Chapter 5: Monitor and
Page 7 and 8:
Chapter 1: Introduction • WebPAM
Page 9 and 10:
PAM Installation Options 3 Chapter
Page 11 and 12:
About This Manual 5 Chapter 1: Intr
Page 13 and 14:
Chapter 2: Installation • Utility
Page 15 and 16:
Install WebPAM 9 Chapter 2: Install
Page 17 and 18:
11 Chapter 2: Installation 7. When
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Chapter 3: Setup • Log-in to WebP
Page 25 and 26:
After sign-in, the WebPAM opening s
Page 27 and 28:
21 Chapter 3: Setup 4. If you want
Page 29 and 30:
23 Chapter 3: Setup 3. Select the r
Page 31 and 32:
25 Chapter 3: Setup 11. Select a St
Page 33 and 34:
Log-out of WebPAM There are two way
Page 35 and 36:
Chapter 4: WebPAM User Interface
Page 37 and 38:
A Host PC’s RAID system is made u
Page 39 and 40:
Event Frame 33 Chapter 4: WebPAM Us
Page 41 and 42: Chapter 5: Monitor and Manage • L
Page 43 and 44: User Management • Add a User (bel
Page 45 and 46: 39 Chapter 5: Monitor and Manage Th
Page 47 and 48: Delete a User 1. In Tree View, clic
Page 49 and 50: 43 Chapter 5: Monitor and Manage 1.
Page 51 and 52: Host Management 45 Chapter 5: Monit
Page 53 and 54: FastTrak 47 Chapter 5: Monitor and
Page 55 and 56: Controller Settings Click on the Se
Page 57 and 58: 4. Click the Delete button. 5. In t
Page 59 and 60: Split a Physical Drive 53 Chapter 5
Page 61 and 62: Media Patrol Schedule 55 Chapter 5:
Page 63 and 64: 57 Chapter 5: Monitor and Manage
Page 65 and 66: 3. Click on the Media Patrol tab in
Page 67 and 68: 4. Click the Locate Drive button. 6
Page 71 and 72: 65 Chapter 5: Monitor and Manage 11
Page 73 and 74: 67 Chapter 5: Monitor and Manage If
Page 75 and 76: 69 Chapter 5: Monitor and Manage
Page 77 and 78: 3. Click on the Migration tab in Ma
Page 79 and 80: Logical Drive Rebuild 73 Chapter 5:
Page 83 and 84: 77 Chapter 5: Monitor and Manage Lo
Page 85 and 86: 3. Click on the Synchronization tab
Page 87 and 88: Identify the Failed Disk Drive 81 C
Page 89 and 90: Enclosures Enclosure View 83 Chapte
Page 91: Spare Drives 85 Chapter 5: Monitor
Page 95 and 96: Chapter 6: Technology Background
Page 97 and 98: RAID 1 - Mirror 91 Chapter 6: Techn
Page 99 and 100: RAID 10 - Mirror / Stripe 93 Chapte
Page 101 and 102: Choosing a RAID Level 95 Chapter 6:
Page 103 and 104: Choosing Stripe Block Size 97 Chapt
Page 105 and 106: Cache Settings 99 Chapter 6: Techno
Page 107 and 108: See the chart below. Current LD Siz
Page 109 and 110: Appendix A: Frequently Asked Questi
Page 111 and 112: Appendix B: Partition and Format In
Page 113 and 114: 107 Appendix A: Partition and Forma
show all

WebPAM User v1.5 - Promise Technology, Inc.

Create successful ePaper yourself

Delete template?

Save as template?