SE Plus-R Â· SEL Plus-R Â· SEM Plus-R - ELV

More documents

Recommendations

Info

GBSetting of the end positions4.3. Mechanic requirementsOperating of the SE Plus-R and SEL Plus-R drives is possible with normal safety andfixing springs. Optionally, security springs can also be used.For operating the SES-R security springs must be used.If the drive is supposed to move against the stop in the upper end position, a stableend stop must be installed!If the drive is set in automatic setup-mode, a limit must be installed for the lower switchoffposition (e.g. windowsill) for the shutter to run against.4.4. Selection table for settings:Setup-mode/end positions inSE Plus SEM Plus SEL Plus SESoperation4.4.1 Automatic setup-mode bottomposition, top stop/release4.4.2 Manual setup-mode bottomposition, top position4.4.3 Manual setup-mode bottomposition, top stop/release4.4.4 Manual setup-mode bottomposition, top stop/no releaseXuP+oPXuP+oAThe abbreviations for the settings types and order:uA = move to stop at bottomuP = store bottom positionoA = move against stop at topoP = store top positiono5cm = store top positon 5 cm before stopXuP+oAXuP+o5cmXoA+uAXuP+oPXuP+oAXoA+uAXuP+oPXuP+oA30
Setting of the end positionsGB4.4.1. Automatic setup-mode for SEL Plus-R and SES-R in operation: bottom position, top stop/releaseWhen the movement is interrupted twice during operation, the system is in automaticsetup-mode. Drive types SEL Plus-R and SES-R will automatically find their stoppositions. For this, a drive must first move against the upper stop and then downwardsuntil it switches off automatically.Important!Only connect that radio drive to power that is to be programmed! You cannot programmore than one drive at the same time.Setting withtransmitterSetting withsettingswitchDrivemovement1. Connect to power.orAuto-Stop top and bottom,keep motion button pressedPROG1 sec.PROG1 sec.2. For setting with transmitter: press the UPand DOWN buttons at the transmitter atthe same time. The transmitter is temporarilytaught into the drive.3. Move the drive upwards with the UP orDOWN button. The correct rotation directionassignment will be performed at theend of the end position setting.4. The drive moves against the upper stopand stops automatically.5. Continue to keep the button pressed orpress one of the motion buttons again.Now the drive automatically movesdown wards.6. The drive will reach the lower limit andstop automatically.7. The end positions are now set and therotation direction assignment is correct.Perform a test run.8. For setting with transmitter: press thePROG button at the transmitter.When setting with setting cable: press theUP and DOWN buttons on the transmitterat the same time, and then thePROG button.9. The transmitter is now permanentlytaught-in.31
Page 1: DGBFNLSE Plus-R · SEL Plus-R ·SEM
Page 4 and 5: DSicherheitshinweise1. Sicherheitsh
Page 6 and 7: DMontage und elektrischer Anschluss
Page 8 and 9: DMontage und elektrischer Anschluss
Page 10 and 11: DEinstellung der Endlagen4.3. Mecha
Page 12 and 13: DEinstellung der Endlagen4.4.2. Man
Page 14 and 15: DEinstellung der Endlagen4.4.4. Man
Page 16 and 17: DNachstellen der Endlage mit dem Ei
Page 18 and 19: DFunktionen im Service-Modus8.2. Ne
Page 20 and 21: D Technische Daten9. Technische Dat
Page 22 and 23: DNotizen22
Page 24 and 25: GBSafety instructions1. Safety inst
Page 26 and 27: GBInstallation and electrical conne
Page 28 and 29: GBInstallation and electrical conne
Page 32 and 33: GBSetting the end positions4.4.2. M
Page 34 and 35: GBSetting the end positions4.4.4. M
Page 36 and 37: GBAdjusting the end position with t
Page 38 and 39: GBFunctions in service mode8.2. Rep
Page 40 and 41: GBTechnical data9. Technical dataSe
Page 42 and 43: DGBNotes42
Page 44 and 45: FConsignes de sécurité1. Consigne
Page 46 and 47: FMontage et raccordement électriqu
Page 48 and 49: FMontage et raccordement électriqu
Page 50 and 51: FRéglage des positions de fin de c
Page 56 and 57: FModification des fins de course av
Page 58 and 59: FFonctions en mode service8.2. Prog
Page 60 and 61: FCaractéristiques techniques9. Car
Page 62 and 63: FDFNotices62
Page 64 and 65: NLVeiligheidsinstructies1. Veilighe
Page 66 and 67: NLMontage en elektrische aansluitin
Page 68 and 69: NLMontage en elektrische aansluitin
Page 70 and 71: NLInstelling van de eindstanden4.3.
Page 76 and 77: NLBijstellen van de eindstand met d
Page 78 and 79: NLFuncties in de Service modus8.2.
Page 80 and 81:
DNLTechnische data9. Technische dat
Page 82:
NLw82
show all

SE Plus-R Â· SEL Plus-R Â· SEM Plus-R - ELV

Create successful ePaper yourself

Delete template?

Save as template?