Threads and Threading - Sportpilot.info

More documents

Recommendations

Info

1806 METRIC SCREW THREADS MJ PROFILE Table 2. ANSI Standard Metric Screw Threads MJ Profile, Diameter-Pitch Combinations for Aerospace ANSI/ASME B1.21M-1997 Nom. Size a Pitch Aerospace Screws, Bolts and Nuts Aerospace Fluid System Fittings Nom. Size Pitch Machinery's Handbook 27th Edition Nom. Size Pitch Nom. Size Pitch Nom. Size Pitch Nom. Size Pitch Nom. Size Pitch 1.6 0.35 5 0.8 14 1.5 27 2 8 1 20 1.5 36 1.5 2 0.4 6 1 16 1.5 30 2 10 1 22 1.5 39 1.5 2.5 0.45 7 1 18 1.5 33 2 12 1.25 24 1.5 42 2 3 0.5 8 1 20 1.5 36 2 14 1.5 27 1.5 48 2 3.5 0.6 10 1.25 22 1.5 39 2 16 1.5 30 1.5 50 2 4 0.7 12 1.25 24 2 … … 18 1.5 33 1.5 … … All dimensions are in millimeters. a For threads smaller than 1.6 mm nominal size, use miuniature screw threads (ANSI B1.10M). Fig. 1. Internal MJ Thread Basic and Design Profiles (Top) and External MJ Thread Basic and Design Profiles (Bottom) Showing Tolerance Zones Copyright 2004, Industrial Press, Inc., New York, NY
TRAPEZOIDAL METRIC THREADS 1807 Tolerances: The thread tolerance system is based on ISO 965/1, Metric Screw thread System of Tolerance Positions and Grades. Tolerances are positive for internal threads and negative for external threads, that is, in the direction of minimum material. For aerospace applications, except for fluid fittings, tolerance classes 4H5H or 4G6G and 4g6g should be used. These classes approximate classes 3B/3A in the inch system. Aerospace fluid fittings use classes 4H5H or 4H6H and 4g6g. Tolerance classes 4G5G or 4G6G and 4g6g are provided for use when thread allowances are required. These classes provide a slightly tighter fit than the inch classes 2B/2A at minimum material condition. Additional tolerance classes 6H/6g are included in this Standard to provide appropriate product selection based on general applications. These classes and the selection of standard diameter/pitch combinations are the same as those provided for the M profile metric screw threads in ANSI/ASME B1.13M. Classes 6H/6g result in a slightly looser fit than inch classes 2B/2A at minimum material condition. Symbols: Standard symbols appearing in Fig. 1 are: D=Basic major diameter of internal thread D 2 =Basic pitch diameter of internal thread D 1 =Basic minor diameter of internal thread d=Basic major diameter of external thread d 2 =Basic pitch diameter of external thread d 1 =Basic minor diameter of internal thread d 3 =Diameter to bottom of external thread root radius H=Height of fundamental triangle P=Pitch Basic Designations: The aerospace metric screw thread is designated by the letters “MJ” to identify the metric J thread form, followed by the nominal size and pitch in millimeters (separated by the sign “×”) and followed by the tolerance class (separated by a dash from the pitch). Unless otherwise specified in the designation, the thread helix is right hand. Example:MJ6 × 1 − 4h6h Machinery's Handbook 27th Edition For further details concerning limiting dimensions, allowances for coating and plating, modified and special threads, etc., reference should be made to the Standard. Trapezoidal Metric Thread Comparison of ISO and DIN Standards.—ISO metric trapezoidal screw threads standard, ISO 2904-1977, describes the system of general purpose metric threads for use in mechanisms and structures. The standard is in basic agreement with trapezoidal metric thread DIN 103. The DIN 103 standard applies a particular pitch for a particular diameter of thread, but the ISO standard applies a variety of pitchs for a particular diameter. In ISO 2904-1977, the same clearance is applied to both the major diameter and minor diameter, but in DIN 103 the clearance in the minor diameter is two or three times greater than clearance in the major diameter. A comparison of ISO 2904 and DIN 103 is given in Table 1. Copyright 2004, Industrial Press, Inc., New York, NY
Page 1 and 2:
SCREW THREAD SYSTEMS 1725 Screw Thr
Page 3 and 4:
Machinery's Handbook 27th Edition O
Page 5 and 6:
Machinery's Handbook 27th Edition T
Page 7 and 8:
SCREW THREADS 1727 ISO Metric Threa
Page 9 and 10:
Machinery's Handbook 27th Edition S
Page 11 and 12:
Machinery's Handbook 27th Edition S
Page 13 and 14:
UNIFIED SCREW THREADS 1733 UN Inter
Page 15 and 16:
Machinery's Handbook 27th Edition U
Page 17 and 18:
Nominal Size, Threads per Inch, and
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36: Nominal Size, Threads per Inch, and
Page 39 and 40: Machinery's Handbook 27th Edition T
Page 43 and 44: Machinery's Handbook 27th Edition U
Page 45 and 46: UNIFIED SCREW THREADS 1765 Table 4c
Page 49 and 50: UNIFIED SCREW THREADS 1769 Table 5d
Page 51 and 52: UNIFIED SCREW THREADS 1771 Table 5e
Page 57 and 58: Machinery's Handbook 27th Edition M
Page 59 and 60: MINIATURE SCREW THREADS 1779 Table
Page 61 and 62: ;; ;;;; ;;;;;; ;;;;;;;; ;;;;;;;;;;
Page 67 and 68: METRIC SCREW THREADS M PROFILE 1787
Page 75 and 76: Pitch P METRIC SCREW THREADS M PROF
Page 81 and 82: Basic Thread METRIC SCREW THREADS M
Page 85: METRIC SCREW THREADS MJ PROFILE 180
Page 89 and 90: TRAPEZOIDAL METRIC THREADS 1809 Tab
Page 91 and 92: 120 140 160 180 110 130 150 170 Mac
Page 95 and 96: Pitch P BRITISH STANDARD ISO METRIC
Page 97 and 98: BRITISH STANDARD ISO METRIC SCREW T
Page 99 and 100: BRITISH STANDARD ISO METRIC SCREW T
Page 101 and 102: Nominal Diametera BRITISH STANDARD
Page 103 and 104: Nominal Diameter BRITISH STANDARD I
Page 105 and 106: Machinery's Handbook 27th Edition A
Page 107 and 108: Machinery's Handbook 27th Edition A
Page 109 and 110: Table 2b. Limiting Dimensions of AN
Page 113 and 114: CENTRALIZING ACME SCREW THREADS 183
Page 117 and 118: Machinery's Handbook 27th Edition C
Page 119 and 120: Table 8c. Limiting Dimensions of Am
Page 123 and 124: Machinery's Handbook 27th Edition S
Page 125 and 126: Table 14b. Limiting Dimensions for
Page 127 and 128: Nominal Sizes Table 15. Stub Acme S
Page 129 and 130: Machinery's Handbook 27th Edition B
Page 131 and 132: Thds. a per Inch ANSI BUTTRESS THRE
Page 133 and 134: ANSI BUTTRESS THREADS 1853 Table 3.
Page 135 and 136: ANSI BUTTRESS THREADS 1855 The majo
Page 137 and 138:
Machinery's Handbook 27th Edition W
Page 139 and 140:
WHITWORTH THREADS 1859 Table 3. Bri
Page 141 and 142:
AMERICAN PIPE THREADS 1861 Table 1a
Page 143 and 144:
AMERICAN PIPE THREADS 1863 guide fo
Page 145 and 146:
Machinery's Handbook 27th Edition A
Page 147 and 148:
DRYSEAL PIPE THREADS 1867 b PTF-SAE
Page 149 and 150:
Machinery's Handbook 27th Edition B
Page 151 and 152:
BRITISH PIPE THREADS 1871 British S
Page 153 and 154:
Page 155 and 156:
HOSE COUPLING SCREW THREADS 1875 Th
show all

Threads and Threading - Sportpilot.info

Create successful ePaper yourself

Delete template?

Save as template?