H-1100 - Smiths Medical

More documents

Recommendations

Info

3 Interlocks S E C T I O N 7 • C o n t r o l s a n d D i s p l a y s The Fluid Warmer has three Interlocks that detect for proper installation of a Disposable Set's components. Refer to the figure to identify the positions of Interlocks. Note: Block 1 is not an Interlock. It cannot detect if a Disposable Set is not correctly installed. It is identified here because it is an essential step for proper installation of the Disposable Set components. The three Interlocks are located on the Fluid Warmer and check for proper installation of: • 2 Heat Exchanger (top end) • 3 Gas Vent • 4 Heat Exchanger (guide) Interlocks 2, 3, and 4 prevent the Fluid Warmer's pump from circulating reservoir solution if the Disposable Set's Heat Exchanger and Gas Vent are not installed properly. If Check Disposables Alarm is Activated on the Fluid Warmer a Check Heat Exchanger for proper installation in Block 1, and Interlocks 2 and 4. b Press Heat Exchanger down firmly in Block 1 to secure in O- Ring. c Press Interlock 2 tab down firmly to engage the Interlock switch. d Check Gas Vent installation in Interlock 3. Level 1 ® NORMOFLO ® H-1100 Irrigation Fluid Warmer | Operator’s Manual 17
SECTION 8 Operation The Level 1 ® NORMOFLO ® H-1100 Irrigation Fluid Warmer (Fluid Warmer) functions are monitored and controlled by two interfaces/control panels located on the Fluid Warmer. The two interfaces are: • Fluid Warmer Power and Alarm Test Panel • Fluid Warmer Display Panel In the table on the following page, operation of the device is represented in terms of the two interfaces that control specific device functions. The numbers call out individual Modes of Operation activated or indicated on the interface. Operational modes • OFF Mode • ON/Automatic Operation for Fluid Warmer • Alarm Test Mode • Over Temperature Test Mode • Check Disposables Mode • Add Recirculating Solution Mode • Over Temperature Alarm Mode The modes of operation are individually defined in the following section. This includes a description of each mode, activation and/or monitoring of the mode, mode characteristics, and clearing of the mode state. 18 Level 1 ® NORMOFLO ® H-1100 Irrigation Fluid Warmer | Operator’s Manual S E C T I O N 8 • O p e r a t i o n
Page 1 and 2: Manufacturer: Smiths Medical ASD, I
Page 3 and 4: Level 1 ® NORMOFLO ® H-1100 Irrig
Page 5 and 6: C o n t e n t s 9.3 After Use 29 10
Page 7 and 8: SECTION 2 Description The Level 1
Page 9 and 10: SECTION 4 Important Safety Informat
Page 11 and 12: CAUTIONS Physical injury to the pat
Page 13 and 14: Step 1 - Verify Components of the F
Page 15 and 16: Step 3 - Attach the Fluid Bag Hange
Page 17 and 18: SECTION 6 Principle of Operation Th
Page 19 and 20: SECTION 7 Controls and Displays Thr
Page 21: Fluid Warmer Display Panel The Flui
Page 25 and 26: Modes of Operation WARNING • If a
Page 27 and 28: Check Disposables Mode The Check Di
Page 29 and 30: SECTION 9 Operating Instructions Th
Page 31 and 32: A-Install the Irrigation Warming Se
Page 33 and 34: C-Attach Disposable Hand Piece or S
Page 35 and 36: SECTION 10 Troubleshooting Only qua
Page 37 and 38: SECTION 11 Testing This unit should
Page 39 and 40: Performance Testing Cold Start Test
Page 41 and 42: Periodic Electrical Testing Earth L
Page 43 and 44: Maintenance Performed Every 12 Mont
Page 45 and 46: Maintenance and Calibration Log All
Page 47 and 48: C. Conditions of Warranty: The warr
Page 49 and 50: • Service and calibration instruc
Page 51 and 52: Electromagnetic Environmental Recom
Page 53 and 54: Symbols Definitions C D 1 V Latex F
Page 55 and 56: Index A Accessories list 46 Add Rec

H-1100 - Smiths Medical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?