StringPin Pinsetter Service Manual - Brunswick

More documents

Recommendations

Info

STring TenSion adjUSTMenTS Section 4 - Adjustments The string tension adjustments can only be made after the pins have been secured to the strings. This adjustment can affect all other adjustments. 1. With the pinsetter power off, lock out the power. Warning! Pinsetter power is to remain off while performing any manual function. 2. Manually rotate the large drive pulley until the top of the pins are in the centering cone with out any slack on the string. The top of the pin should touch the bottom of the centering cone 3. Lock the large drive pulley in this position. 4. If the pins won`t come into the centering cone, go to Step 5. 5. Slide the string spool to the left away from the locking pin. Refer to Figure 4-1. 6. Rotate the string spool as required to obtain a gap of 1 mm to 5 mm between the limiter bar and the tension lever. Refer to Figure 4-1. 7. When the proper gap has been obtained, move the string spool to the right and rotate it as required to align one of its holes with the locking pin. Refer to Figure 4-1. NOTE: Rotating the spool as arrow (4) shows will reduce the tension. Rotating the spool as arrow (3) shows will increase the tension. Refer to Figure 4-1. Figure 4-1. String Tension Adjustments 1 PINSETTER CYCLED TO PINS UP POSITION 2 LIMITER BAR 3 TENSION LEVER 4 TURN AS ARROw SHOwS TO INCREASE EXTENSION 5 TURN AS ARROw SHOwS TO DECREASE EXTENSION 6 AwAY FROM LOCKING PIN 7 TOwARD LOCKING PIN 8 LOCKING PIN 9 LARGE DRIVE PULLEY 10 STRING SPOOL 16 StringPin Pinsetter Service Manual
STring BraKe adjUSTMenTS 1. With the pinsetter power on, knock over some pins. The machine will cycle and should keep the knocked over pins in the up position. 2. Turn the pinsetter power off and lockout the power on/off switch. Warning! Pinsetter power is to remain off while performing any manual function. 3. Check the movement of the pin in the pin centering cone by pulling on the string. The travel of the pin movement should be 80 mm ± 20 mm. Refer to Figure 4-2. Figure 4-2. String Brake Adjustment 1 CENTERING CONE StringPin Pinsetter Service Manual 17
Page 1 and 2: Service Manual StringPin Pinsetter
Page 3 and 4: ConTenTS Section 1 - SAFETY! ......
Page 5 and 6: noTeS & WarningS Section 1 - SAFETY
Page 7 and 8: CenTer MeChaniC Center Mechanics ar
Page 9 and 10: PinSeTTer iS ready for BoWling Figu
Page 11 and 12: PinSeTTer SWiTCh fUnCTionS disentan
Page 13 and 14: String Brake Switch The string brak
Page 15: String Control Unit (Spic) The stri
Page 19 and 20: Pin SloW SeTTing adjUSTMenTS 1. Tur
Page 21 and 22: fallen Pin deTeCTion adjUSTMenT The
Page 23 and 24: 3. Thread the string through the he
Page 25 and 26: 8. Wind the extra string onto the s
Page 27 and 28: quarterly (3 Month) - Apply grease
Page 29 and 30: - Apply a drop of oil on each side
Page 31 and 32: Section 6 - Troubleshooting SolUTio
Page 33 and 34: Section 7 - Cable Routing and Conne
Page 35 and 36: Figure7-1. Odd Lane Electrical Cont
Page 37 and 38: StringPin Pinsetter Figure 7-3. Bal
Page 39 and 40: Figure 7-5. Ball Detect StringPin P
Page 41 and 42: Figure 7-7. Motor StringPin Pinsett
Page 43 and 44: PCB Components and Connections Stri
Page 45 and 46: (21) Main Power - Input power conne
Page 47 and 48: (9) Seileinzug - A push button is c
Page 49 and 50: Figure 7-12. Overview of Buttons on
Page 51 and 52: Figure 7-15. Route Interface Cable
Page 53 and 54: 3. Center the ball detect assembly
Page 55 and 56: SES String Machine Figure 7-21. “
Page 57 and 58: Figure 7-23 StringPin Pinsetter Ser
Page 59 and 60: The following is a description of t
Page 61 and 62: (37) LED D35-D44 - Used to indicate
Page 63 and 64: Scanner Data - Cable Assembly (P/N
Page 65: On/Off Reset - Cable Assembly (P/N

StringPin Pinsetter Service Manual - Brunswick

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?