StringPin Pinsetter Service Manual - Brunswick

More documents

Recommendations

Info

lUBriCaTion routine Regular lubrication of the machine is necessary for a long machine life and good performance. The interval should be appropriate for the amount the machine is used. The more the machine is used, the more frequently it should be serviced. - Every moving machine part should be lubricated from time to time. - Every working part such as drive gears and drive chains, require more maintenance than low load parts. - For large parts such as drive gears and chain sprockets, grease is the best lubricant - For small parts, oil should be used. 26 StringPin Pinsetter Service Manual
quarterly (3 Month) - Apply grease to the chain with a paint brush to lubricate the chain`s exterior. Refer to Figure 5-4 - Lubricate the chain with oil. This oil will penetrate chain links to lubricate the chain’s interior. Refer to Figure 5-4. . - Apply oil to the pivot point where the string wagon is attached to the chain. Refer to Figure 5-4. Figure 5-4. Lubrication Locations 1 GREASE CHAIN wITH PAINT BRUSH 2 STRING wAGON / CHAIN ROLLER SHAFT, USE OIL 3 PIVOT / STRING wAGON / CHAIN. USE OIL Semi annually (6 Month) 4 REMOVE COVER TO GREASE GEAR (BE CAREFUL NOT TO GET GREASE ON THE “V” BELT) 5 GEAR, GREASE ACCESS HOLE 6 GREASE SPRING LEVER 7 GREASE STRING ROLLER SHAFT 8 CHAIN SPROCKET, GREASE ACCESS HOLE - Grease through hole in switch cluster over located on the right side of the rear of the pinsetter. Refer to Figure 5-4. - Remove cover from the motor and gear assembly located on the left side of the rear of the machine and grease gear. Refer to Figure 5-4. - Press grease in chain gears through hole in plate located on the outside of pinsetter frame adjacent to gear. Refer to Figure 5-4. StringPin Pinsetter Service Manual 27
Page 1 and 2: Service Manual StringPin Pinsetter
Page 3 and 4: ConTenTS Section 1 - SAFETY! ......
Page 5 and 6: noTeS & WarningS Section 1 - SAFETY
Page 7 and 8: CenTer MeChaniC Center Mechanics ar
Page 9 and 10: PinSeTTer iS ready for BoWling Figu
Page 11 and 12: PinSeTTer SWiTCh fUnCTionS disentan
Page 13 and 14: String Brake Switch The string brak
Page 15 and 16: String Control Unit (Spic) The stri
Page 17 and 18: STring BraKe adjUSTMenTS 1. With th
Page 19 and 20: Pin SloW SeTTing adjUSTMenTS 1. Tur
Page 21 and 22: fallen Pin deTeCTion adjUSTMenT The
Page 23 and 24: 3. Thread the string through the he
Page 25: 8. Wind the extra string onto the s
Page 29 and 30: - Apply a drop of oil on each side
Page 31 and 32: Section 6 - Troubleshooting SolUTio
Page 33 and 34: Section 7 - Cable Routing and Conne
Page 35 and 36: Figure7-1. Odd Lane Electrical Cont
Page 37 and 38: StringPin Pinsetter Figure 7-3. Bal
Page 39 and 40: Figure 7-5. Ball Detect StringPin P
Page 41 and 42: Figure 7-7. Motor StringPin Pinsett
Page 43 and 44: PCB Components and Connections Stri
Page 45 and 46: (21) Main Power - Input power conne
Page 47 and 48: (9) Seileinzug - A push button is c
Page 49 and 50: Figure 7-12. Overview of Buttons on
Page 51 and 52: Figure 7-15. Route Interface Cable
Page 53 and 54: 3. Center the ball detect assembly
Page 55 and 56: SES String Machine Figure 7-21. “
Page 57 and 58: Figure 7-23 StringPin Pinsetter Ser
Page 59 and 60: The following is a description of t
Page 61 and 62: (37) LED D35-D44 - Used to indicate
Page 63 and 64: Scanner Data - Cable Assembly (P/N
Page 65: On/Off Reset - Cable Assembly (P/N

StringPin Pinsetter Service Manual - Brunswick

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?