StringPin Pinsetter Service Manual - Brunswick

More documents

Recommendations

Info

4. If travel is greater than 100 mm, move the string brake switch up. Refer to Figure 4-3. Figure 4-3. Adjust Brake Switch 1 STRING BRAKE SwITCH 2 LOOSEN SCREwS TO ADJUST 3 SLIDE SwITCH HOLDER UP OR DOwN 5. If the travel is less than 60 mm, move the string brake switch down. 6. Repeat steps 1-3 to verify pin movement in pin centering cone. 18 StringPin Pinsetter Service Manual
Pin SloW SeTTing adjUSTMenTS 1. Turn the pinsetter power on. Knock down some pins. When the string wagon travels to the rear of the string pinsetter, turn off the pinsetter power 2. With the pinsetter power off, lock out the power 3. The pins will travel to the pindeck by gravity Warning! Pinsetter power is to remain off while performing any manual function. 4. Manually rotate the large drive pulley in reverse, raising the pins until the string wagon lever roller starts to touch the pin slow setting cam. 5. Lock the large drive pulley at this position 6. Measure the distance the bottom of pins 1, 2, and 3 are from the pin deck. The distance should be 60mm +-20mm. Measure the distance the bottom of pins 4 – 10 are from the pin deck. The distance should be 80mm +- 20mm StringPin Pinsetter Service Manual 19
Page 1 and 2: Service Manual StringPin Pinsetter
Page 3 and 4: ConTenTS Section 1 - SAFETY! ......
Page 5 and 6: noTeS & WarningS Section 1 - SAFETY
Page 7 and 8: CenTer MeChaniC Center Mechanics ar
Page 9 and 10: PinSeTTer iS ready for BoWling Figu
Page 11 and 12: PinSeTTer SWiTCh fUnCTionS disentan
Page 13 and 14: String Brake Switch The string brak
Page 15 and 16: String Control Unit (Spic) The stri
Page 17: STring BraKe adjUSTMenTS 1. With th
Page 21 and 22: fallen Pin deTeCTion adjUSTMenT The
Page 23 and 24: 3. Thread the string through the he
Page 25 and 26: 8. Wind the extra string onto the s
Page 27 and 28: quarterly (3 Month) - Apply grease
Page 29 and 30: - Apply a drop of oil on each side
Page 31 and 32: Section 6 - Troubleshooting SolUTio
Page 33 and 34: Section 7 - Cable Routing and Conne
Page 35 and 36: Figure7-1. Odd Lane Electrical Cont
Page 37 and 38: StringPin Pinsetter Figure 7-3. Bal
Page 39 and 40: Figure 7-5. Ball Detect StringPin P
Page 41 and 42: Figure 7-7. Motor StringPin Pinsett
Page 43 and 44: PCB Components and Connections Stri
Page 45 and 46: (21) Main Power - Input power conne
Page 47 and 48: (9) Seileinzug - A push button is c
Page 49 and 50: Figure 7-12. Overview of Buttons on
Page 51 and 52: Figure 7-15. Route Interface Cable
Page 53 and 54: 3. Center the ball detect assembly
Page 55 and 56: SES String Machine Figure 7-21. “
Page 57 and 58: Figure 7-23 StringPin Pinsetter Ser
Page 59 and 60: The following is a description of t
Page 61 and 62: (37) LED D35-D44 - Used to indicate
Page 63 and 64: Scanner Data - Cable Assembly (P/N
Page 65: On/Off Reset - Cable Assembly (P/N

StringPin Pinsetter Service Manual - Brunswick

Create successful ePaper yourself

Delete template?

Save as template?