CDV34 Gas Fireplace - Continental Fireplaces

More documents

Recommendations

Info

6 24 1/4” MINIMUM 10” MINIMUM (BCDV34) 24” MINIMUM (CDV34) 53 5/8” W415-0345 / L / 03.05.09 TYPICAL VENT INSTALLATIONS FIGURES 2a - d 24” MAXIMUM 8” MINIMUM (BCDV33) 12” MINIMUM (CDV33) * REFER TO “VENTING SECTION” MAXIMUM HORIZONTAL RUN 16” MINIMUM 40 FT MAXIMUM 36” MINIMUM 24” MAX 11” MIN 1” RISE / FT * 12” MINIMUM TO GRADE FIGURE 3a - b 1” RISE/FT* VENT INSTALLATIONS 30” MINIMUM MAXIMUM 10 FEET VENT LENGTH TOP EXIT INSTALLATION 33 FEET MAXIMUM 7 FEET MAXIMUM 40 FT MAXIMUM 36” MINIMUM F I G U R E 4 a - b 6” RISE 12” MINIMUM CORNER INSTALLATION 16” MINIMUM BCDV33 and CDV33: When venting straight out the back, only the rigid * REFER TO “VENTING SECTION” vent can be used. Do not use flexible vent. For all other venting configurations, flexible vent is acceptable. When venting either a CDV33 or a BCDV33, the horizontal run must be kept to a maximum of 24 inches. A CDV33 must be kept to a minimum of 12 inches and a BCDV33 must be kept to a minimum of 8 inches. When terminating vertically, the vertical rise is a minimum 36 inches to a maximum 40 feet from the centre of the fireplace flue outlet. ALL MODELS: Vent lengths that pass through unheated spaces (attics, garages, crawl spaces) should be insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for visually checking the vent connection to the fireplace after the fireplace is installed. Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼" air gap between the inner and outer liner all around is required for safe operation. Use a firestop, vent pipe shield or attic insulation shield when penetrating interior walls, floor or ceiling. Minimum clearance to combustible construction from fireplace and vent surfaces: BCDV33 CDV33 BCDV34 CDV34 SIDE OF THE UNIT 0" 0" 0" 0" BACK OF THE UNIT 0" 0" 0" 0" BOTTOM OF THE UNIT 0" 0" 0" 0" TOP OF THE UNIT 0" 0" 0" 51 TABLE 2 /8"** TOP OF THE VENT PIPE 2"* 2"* 2" 2" SIDES OF THE VENT PIPE 1" 1" 1" 1" BOTTOM OF THE VENT PIPE 1" 1" 1" 1" RECESSED DEPTH 13" 13" 13" 13" * A clearance to combustibles of 2" at the vent pipe top must be maintained. The firestop spacer W010-1777supplied with the unit must be used to maintain this clearance. ** The first 5 1/8" of finishing material above the CDV34 must be non-combustible. The header must be steel. For safe and proper operation of the fireplace follow the venting instruction exactly. Deviation from the minimum or the maximum vertical vent length can create difficulty in burner start-up and/ or carboning. A terminal shall not terminate directly above a sidewalk or paved driveway which is located betweeen two single family dwellings and serves both dwellings. Local codes or regulations may require different clearances. In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the fireplace body, it is recommended that the walls of the fireplace enclosure be “finished” (ie: drywall/sheetrock), as you would finish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity. Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp and American Metal Amerivent venting systems must not be combined. Purge all gas lines with the glass door of the fireplace open. Assure that a continuous gas flow is at the burner before closing the door. Under extreme vent configurations, allow several minutes (5-15) for the flame to stabilize after ignition. Six (6") inches is the minimum bend radius allowed for the 7" diameter flexible liner. FOR SPECIFIC VENTING PARAMETERS, REFER TO PAGES 9-14.
MINIMUM AIR TERMINAL LOCATION CLEARANCES FIGURE 5 W415-0345 / L / 03.05.09 7
Page 1 and 2: $10.00 W415-0345 / L / 03.05.09 1
Page 3 and 4: Continental® products are manufact
Page 5: 35" FIGURE 1a FIGURE 1b 33 1 /8" FI
Page 9 and 10: for the following symbols used in t
Page 11 and 12: when (H T ) < (V T ) Simple venting
Page 13 and 14: when (H T ) < (V T ) Simple venting
Page 15 and 16: INSTALLATION WALL AND CEILING PROTE
Page 17 and 18: 1. Cut or frame a hole in an exteri
Page 19 and 20: EXTENDED HORIZONTAL AND CORNER AIR
Page 21 and 22: FIGURE 39 a-d 33 1 /4" MIN. 34 3/4"
Page 23 and 24: CDV34 ONLY: Finishing must be done
Page 25 and 26: Blocked burner ports can cause an i
Page 27 and 28: FIGURE 56 C B L334 LOUVRE INSTALLAT
Page 29 and 30: OPERATION / MAINTENANCE Purge all g
Page 31 and 32: Contact your dealer for questions c
Page 33 and 34: 11 65 64 COMMON REPLACEMENTS BCDV33
Page 35 and 36: SYMPTOM PROBLEM TEST SOLUTION Main

CDV34 Gas Fireplace - Continental Fireplaces

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?