shop main D-2011 - Moto-Services

ACCESSORIES
SUSPENSION
CONTROL
IGNITION/ELECTRICAL
CARB & FUEL
HARD PARTS SHOP EQUIP & TOOLS
80
WINONA VAN NORMAN SERVICE EQUIPMENT
35-2765
35-0458
35-2769
35-2766
WINONA CB1401 CYLINDER BORING BAR
The CB1401 is the fastest and most efficient boring machine you can
buy. With simple, accurate setup, the CB1401handles cylinders from
1.5” to 4”, up to .040” can be removed in one pass. Standard features
include a direct reading micrometer**, centering cone, anti-vibration
tool, automatic upper and lower feed stops and two parallels.
**Available in SAE or Metric, please specify when ordering.
35-4316 CB1401 Cylinder Boring Bar with 120V 60Hz 1Ph motor
35-4319 CB1401 Cylinder Boring Bar with 220V 50Hz 1Ph motor
OPTIONAL EQUIPMENT
35-0458 Big Bore Kit-Increases range from 4” to 4-1/2”
35-4317 3 Finger Centering Device
35-4318 Replacement Carbide Inserts
35-2769 Dial Indicator Centering Fixture (Part# 2408)
35-2765 Dial Depth Indicator Manual Kit (Part# 1715)
35-2766 Dial Depth Indicator, DRO Z-Axis (Part# 1716)
35-2747 Brass Tipped Set Screw (Part# 801429)
35-2748 3/16 Brass Tipped Set Screw (Part# 801396)
35-2749 SAE Tool Setting Micrometer (Part# 5121)
35-2768 Metric Tool Setting Micrometer (Part# 5122)
Specifications:
Range: 1.5” (38mm) - 4” (101mm) Travel: 8” (203mm)
Speeds: 222 & 335 RPM Ship Weight: 550 lbs. (249kg)
Spray Washer for heads,
blocks and engine components.
Adjustable
thermostat gives quick
heat up. Double-lipped
door seal prevents leaks.
60-min. timer, 3 HP
motor, and 1000 lb.
capacity are standard
35-2736 WVN3226
Spray Washer
Single carbide insert
machines three angles
simultaneously. Pilot is
supported on both
ends, with holders to fit
the smallest valve seats.
Ball joint allows 15°
degree of movement
35-2741 VSG22 Seat
Cutter (Manual)
WINONA PS1370 CYLINDER HONING MACHINE
The PS1370 produces a consistent surface finish. Cylinders are easy to
set up and hone with the standard small engine fixture. It handles
singles and many twins, triples, and fours, and will hone cylinders
with torque plate attached. Shipping Weight is 400 lbs. (181kg)
Honing Machine includes Honing Oil Pump, Work Light, Small
Engine Fixture, 1/2” Jacobs Chuck Kit and 5 Gallons of Honing Oil.
35-0454 PS1370 Cylinder Honing Machine, 110V 60Hz 1PH
35-0455 PS1370 Cylinder Honing Machine, 220V 50Hz 1PH
OPTIONAL EQUIPMENT
35-0456 Hone Head with Dual Friction Feed
35-0457 Junior Hone Head with Dual Friction Feed
Specifications:
Range: 2.5” (66mm) - 5.6” (142mm) Stroke: Up to 10” (254mm)
Air Required: 110 PSI @ 3 cfm Motor: 1/4 H.P.
Designed for ease and
safety of operation
during honing. Your
motorcycle cylinders
are easy to set up with
the standard small
engine fixture. It's easy
to use, accurate, and
affordable for any shop.
35-2737 CH1300
Honing Tank
Easy to operate, with
valves clamped in the
head stock by a collet.
Base is cast, Valve headstock
has an adjustment
range from 30° to 60°.
Longitudinal and
transverse carriages
slide on dovetail guides.
35-2770 V50 Valve
Grinder
Holds 100 Gal of
solution, with insulated
tank and lid. Large 22 x
34 inch basket has 500Lb.
weight capacity.
Thermostat for temperature
control, 1/2 HP.
motor. Removable
bottom crate for easy
clean out of sludge.
35-2738 HT100
Hot Tank
Used to check bend &
twist in connecting
rods, four expanding
mandrels makes set-up
fast, eliminating operator
error. Includes: 2
Dial Indicators, 4
Expanding Pins, 4
Alignment Arbors.
35-2745 RAF120
Rod Fixture