shop main D-2011 - Moto-Services

VALVE GUIDE DRIVERS
Use for removal and installation of valve guides into cylinder head.
35-8388 4.0mm YM-04111 35-8418 4.5mm YM-04116
35-8416 6.0mm YM-04064-A 35-8417 5.0mm YM-04097
35-8414 7.0mm YM-01225-A 35-8408 5.5mm YM-01122
35-8413 8.0mm YM-01200
YAMAHA VALVE GUIDE INSTALLERS
These installers are used for installation of Yamaha shoulderless valve
guides to a specific depth into the cylinder head. To use, position onto
the valve guide and drive into the cylinder head until installer makes
contact with cylinder head surface. Note: Must use with Valve Guide
Driver. Available in the following sizes:
35-8387 4.0mm YM-04112
35-8439 4.5mm YM-04117
35-8437 5.0mm YM-04098
35-8419 5.5mm YM-04015
35-8435 6.0mm
35-8423 7.0mm
YM-04065-A
YM-04017
35-8423 35-8435
VALVE GUIDE REAMERS
Reaming valve guides after installation assures a proper valve stem
to valve guide fit. Available in the following sizes:
35-3854 4.0mm YM-04113 35-3829 4.5mm YM-04118
35-3847 6.0mm YM-04066 35-3835 5.0mm YM-04099
35-3851 7.0mm YM-01227 35-3836 5.5mm YM-01196
35-3852 8.0mm YM-01211
FULL BORE RACING VALVE STEM
SEAL INSTALLERS
Designed for the installation of
Valve Stem Seals on modern
Shim Under Bucket 4-stroke
street, ATV and Dirtbike heads.
These tools can hold up to 4
Valve Stem Seals and
load them onto the valve guides
in under 15 seconds. Sold each.
35-2771 Full Bore Racing Valve Stem Seal Installers (4.0)
35-2773 Full Bore Racing Valve Stem Seal Installer (4.5)
35-2776 Full Bore Racing Valve Stem Seal Installer (5.0)
35-2778 Full Bore Racing Valve Stem Seal Installer (5.0 Hyabusa)
CYLINDER HEAD REPAIR
KWIK-LOADER VALVE KEEPER TOOL SET
The Kwik-Loader cuts valve insatallation and removal time
drastically. It’s compact and easy to use design replaces bulky
C-clamp style compressors. The white tool is used for keeper
removal, simply slide it over the spring pack/retainer and use
a mallet to apply downward pressure to the collar. Remove
the tool and keepers are ready to take out. To re-assemble, put
valve into the guide, install the springs, and place retainer and
keepers in position. Using the black tool, hand pressure is sufficient
to complete the installation process. It’s easier and
faster than automotive style compressors, and you can even
change valve stem seals without removing cylinder heads.
Simply apply air pressure to the assembled head via the spark
plug hole, and follow the same procedure above. Save time
and make more money, contact your representative for details.
35-3568 Kwik Loader Keeper Installation/Removal Tool
Visit for Demos!
kwikloader.klsupply.com
VALVE GUIDE DRIVER SET (REMOVE & REPLACE)
Designed for speed and accuracy, this eleven piece set provides the
right tool for the job. Driver set includes two valve guide drivers
(5.5mm and 6.6mm), four valve guide installers, one cutter, three cutter
pilots (5.5mm, 6.6mm, and 7.7mm) and one tap handle extension bar.
35-9445 Valve Guide Driver Set (Remove & Replace)
VALVE GUIDE FLEX-HONES (320 GRIT)
Available in the following I.D. sizes:
35-9243 4.0mm 35-9246 6.0mm
35-9245 5.0mm 35-9247 7.0mm
35-9244 5.5mm 35-9248 8.0mm
VALVE LAPPING TOOL
The ultimate vacuum stick for perfect surfaces on valves and valve
seats. Interchangeable cups make unit suitable for use with virtually
any size valve. Set includes vacuum stick, 3/4” and 1/4” rubber cups.
35-8998 Valve Lapping Tool
SHOP EQUIP & TOOLS HARD PARTS CARB & FUEL IGNITION/ELECTRICAL CONTROL SUSPENSION ACCESSORIES
91