IPC@CHIP Documentation - SC12 @CHIP-RTOS V1.10

More documents

Recommendations

Info

IPC@CHIP Documentation Index External Disk Drive External Disk Interface - SC12 @CHIP-RTOS V1.10 Here is the interface definition for an external disk B: drive . This interface allows you to add an external B: drive. This drive must be block (sector) oriented. Each sector should be 512 bytes long. The application must provide a software interrupt 0xB1 function to read and write these sectors on this drive. Maximum disk size is about 2 Gigabytes. ● Interrupt_0xB0_function_0x01:_Install External Disk ● Interrupt_0xB0_function_0x02:_Deinstall External Disk Interrupt 0xB0 service 0x01: Install External Disk This function will logically install a B: drive. Prior to this call the application must provide a disk read/write function installed at interrupt 0xB1. This installed handler function should expect: Parameters AH AX 1 for write, 0 for read. BX,DX Sector number (BX is MSH of unsigned long) CX Number of sectors to read/write ES:DI Segment:Offset of memory area to read/write The handler should return 0 in AX if OK. 0x01 BX,DX An unsigned long with the total number of sectors. BX holds high word. Return Value Top of list Index page AX is 0 if OK. Page 386 / 400
Interrupt 0xB0 service 0x02: Deinstall External Disk Parameters AH Used to deinstall drive B: which was installed before with function 0x01 (above). 0x02 Return Value Top of list Index page AX =0 success AX !=0 failed (may be drive was not installed?) End of document Page 387 / 400
Page 1 and 2:
IPC@CHIP Documentation index - SC12
Page 3 and 4:
available from the download area of
Page 5 and 6:
IPC@CHIP Documentation Index Introd
Page 7 and 8:
1. Timer procedures must be impleme
Page 9 and 10:
Top of list Index page Usage of the
Page 11 and 12:
Top of list Index page Using Hardwa
Page 13 and 14:
Top of list Index page 3. Since @CH
Page 15 and 16:
Top of list Index page End of docum
Page 17 and 18:
IPC@CHIP Documentation Index COMMAN
Page 19 and 20:
Index page TYPE file Type a file. T
Page 21 and 22:
Example rd temp Top of list Index p
Page 23 and 24:
Top of list Index page ALE Enable/d
Page 25 and 26:
Related Topics Top of list Index pa
Page 27 and 28:
Top of list Index page Initial BATC
Page 29 and 30:
Comments Example Make sure that oth
Page 31 and 32:
Comments Top of list Index page tas
Page 33 and 34:
CHIP.INI Documentation - SC12 @CHIP
Page 35 and 36:
STDIO ● SERIAL_EXT_DMA ● SERIAL
Page 37 and 38:
The new mode is shown on the consol
Page 39 and 40:
Top of list Index page IP ADD_DEFAU
Page 41 and 42:
Top of list Index page [PPPCLIENT]
Page 43 and 44:
Example: REMOTEADDRESS=192.168.205.
Page 45 and 46:
IDLETIME=500 By default, PPP server
Page 47 and 48:
Top of list Index page PPP server c
Page 49 and 50:
Comments Example: INITRETRIES0=2 Th
Page 51 and 52:
[PPPSERVER] CTRLTIMEOUTx=timeout in
Page 53 and 54:
PPPSERVER [PPPSERVER] HANGUPANSWERx
Page 55 and 56:
Top of list Index page PPPSERVER [P
Page 57 and 58:
Example: Top of list Index page FTP
Page 59 and 60:
Top of list Index page FTP PASSWORD
Page 61 and 62:
WEB [WEB] TEMPPATH=Name of a tempor
Page 63 and 64:
Top of list Index page WEB The cons
Page 65 and 66:
WEB [WEB] SEC_PASSWORDx=Define a pa
Page 67 and 68:
USERx=user Comments Top of list Ind
Page 69 and 70:
TRACE [TRACE] INTNOTSUPP=0/1 Commen
Page 71 and 72:
Top of list Index page SERIAL [SERI
Page 73 and 74:
MEMGAP=Paragraphs Comments Sets a m
Page 75 and 76:
IPC@CHIP Documentation Index CONFIG
Page 77 and 78:
● Interrupt_0xA0_function_0x19:_C
Page 79 and 80:
Top of list Index page AX = 0. (Thi
Page 81 and 82:
Comments Top of list Index page DI
Page 83 and 84:
ES:DX Pointer to a 16 byte memory a
Page 85 and 86:
Index page Interrupt 0xA0 service 0
Page 87 and 88:
Parameters AH Must be 0x15 Return V
Page 89 and 90:
AH ES:DI Comments Must be 0x20. Add
Page 91 and 92:
int iniPutString(char *sectionName,
Page 93 and 94:
Get the IPC@CHIP device names Param
Page 95 and 96:
Return Value Comments AL= 1 DX=0: S
Page 97 and 98:
Parameters AH AL BX Must be 0x33. B
Page 99 and 100:
void huge my_putstr(char * pch, int
Page 101 and 102:
Index page Interrupt 0xA0 service 0
Page 103 and 104:
Parameters AH ES:DX Top of list Ind
Page 105 and 106:
● Interrupt_0xAC_function_0x0B:_A
Page 107 and 108:
Socket descriptor Return Value DX =
Page 109 and 110:
put into the buffer. The sender can
Page 111 and 112:
The application sleeps for a specif
Page 113 and 114:
Top of list Index page Interrupt 0x
Page 115 and 116:
for the API_SEND function (or recv_
Page 117 and 118:
a new connection. Related Topics To
Page 119 and 120:
AH BX ES:DI 0x16 (= API_SETSOCKOPT)
Page 121 and 122:
Interrupt 0xAC service 0x19: API_RE
Page 123 and 124:
Page 125 and 126:
SocketInfo s[64]; int avail, i; ava
Page 127 and 128:
Comments AX = -2 (=API_NOT_SUPPORTE
Page 129 and 130:
Tests if PPP server is available in
Page 131 and 132:
Index page Interrupt 0xAC service 0
Page 133 and 134:
DS:SI CX 6 Get pointer to AtEntry d
Page 135 and 136:
Bits of AX and DX contains the requ
Page 137 and 138:
Parameters AH 0x74 (= TCPIP_STATIST
Page 139 and 140:
Structure at [ES:DI] is filled with
Page 141 and 142:
Parameters AH ES:DI 0x7A (= IP_USER
Page 143 and 144:
This function is used to delete the
Page 145 and 146:
Page 147 and 148:
CX Number of data structures in arr
Page 149 and 150:
DS:SI Output Parameter: Pointer to
Page 151 and 152:
For more detailed description see H
Page 153 and 154:
BX CX ES:DI Number of available rec
Page 155 and 156:
Page 157 and 158:
IPC@CHIP Documentation Index TCP/IP
Page 159 and 160:
TCP/IP Application Developers Note
Page 161 and 162:
ArpHeader Address Resolution Protoc
Page 163 and 164:
Top of list Index page This buffer
Page 165 and 166:
Comments This data structure and sp
Page 167 and 168:
Comments These structures are only
Page 169 and 170:
Comments unsigned long ipReasmOKs;
Page 171 and 172:
typedef struct tag_ping_command { i
Page 173 and 174:
The PPPDial structure is used durin
Page 175 and 176:
Related Topics ❍ optionName=PPP_I
Page 177 and 178:
SetSocketOption Comments This data
Page 179 and 180:
Top of list Index page UdpMib Comme
Page 181 and 182:
Programming client server applicati
Page 183 and 184:
RTOS API - SC12 @CHIP-RTOS V1.10 IP
Page 185 and 186:
AH BX 0 (=RTX_SLEEP_TIME) Sleep tim
Page 187 and 188:
Page 189 and 190:
Return Value Comments DX=0 (always
Page 191 and 192:
An out of range priority value (CX)
Page 193 and 194:
Comments DX!=0 failure AX: contains
Page 195 and 196:
BX ES:DI 0x19 (= RTX_RESERVE_RES) I
Page 197 and 198:
Top of list Index page RTX_GET_SEM
Page 199 and 200:
BX:SI Output Parameter: Pointer to
Page 201 and 202:
ES:DI CX Output Parameter: Pointer
Page 203 and 204:
Comments DX!=0 failure AX: contains
Page 205 and 206:
The task name is not a null termina
Page 207 and 208:
Page 209 and 210:
AH BX ES:DI DS:SI 0x40 (= RTX_CREAT
Page 211 and 212:
Interrupt 0xAD service 0x43: RTX_WA
Page 213 and 214:
ES:DI 0x46 (= RTX_FIND_EVENTGROUP)
Page 215 and 216:
ES:DI Pointer to a 12 byte message
Page 217 and 218:
Interrupt 0xAD service 0x55: RTX_FI
Page 219 and 220:
Multitasking with @Chip-RTOS Some c
Page 221 and 222:
ackground data base search in the e
Page 223 and 224:
Suspended Free to run RTX_Resume_Ta
Page 225 and 226:
Figure 1 ) Sleep Based Periodic Loo
Page 227 and 228:
can potentially interrupt execution
Page 229 and 230:
} } Figure 5 ) Protected Critical S
Page 231 and 232:
RTOS Overview - SC12 @CHIP-RTOS V1.
Page 233 and 234:
Time / Date Services The following
Page 235 and 236:
Top of list Index page is willing t
Page 237 and 238:
system's maximum number of availabl
Page 239 and 240:
Prior to making the RTX_TASK_CREATE
Page 241 and 242:
B4: Message Exchange wait B5: -- no
Page 243 and 244:
name or void huge MyTimerProc(unsig
Page 245 and 246:
IPC@CHIP Documentation Index @CHIP-
Page 247 and 248:
RTOS Application Developers Note -
Page 249 and 250:
DOS Interface Documentation - SC12
Page 251 and 252:
Parameters AH DL 0x02 Character to
Page 253 and 254:
AH 0x08 Return Value Comments Retur
Page 255 and 256:
AH 0x19 Return Value AL = drive whe
Page 257 and 258:
Page 259 and 260:
Only ten DTA entries for user tasks
Page 261 and 262:
Note: Top of list Index page In @CH
Page 263 and 264:
Parameters AH CX 0x3C File attribut
Page 265 and 266:
Page 267 and 268:
Top of list Index page Get/Set File
Page 269 and 270:
BX DX Handle Device data Return Val
Page 271 and 272:
A paragraph is 16 bytes in length.
Page 273 and 274:
Comments Top of list Index page AX
Page 275 and 276:
operations such as renaming, moving
Page 277 and 278:
AL BX CX DX AL=0 to get the date an
Page 279 and 280:
Page 281 and 282:
Hardware API - SC12 @CHIP-RTOS V1.1
Page 283 and 284:
Top of list Index page if ALE is us
Page 285 and 286:
Page 287 and 288:
Comments If on a given timer the ex
Page 289 and 290:
AH AL Must be 0x88. DRQ channel: 0
Page 291 and 292:
AH ES:DI Must be 0x90. Pointer to a
Page 293 and 294:
Comments 8 Bit data in ax, ax = (da
Page 295 and 296:
Parameters AH DX BX CX Must be 0x83
Page 297 and 298:
Top of list Index page RTX_SIGNAL_E
Page 299 and 300:
none Related Topics Top of list Ind
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
instead be the frequency reported b
Page 307 and 308:
Return Value none Comments Top of l
Page 309 and 310:
Starts the DMA mode. After calling
Page 311 and 312:
BX:SI ES:DI 1 = DRQ1 Output Paramet
Page 313 and 314:
Return Value none Comments Call thi
Page 315 and 316:
Hardware API Layers - SC12 @CHIP-RT
Page 317 and 318:
This function initializes the I2C b
Page 319 and 320:
AL CX Slave address, LSB:0 => Trans
Page 321 and 322:
AH AL 0x8F PIO pin number, [0..13]
Page 323 and 324:
AH ES:DI CX Must be 0x96 Pointer to
Page 325 and 326:
I2C Bus and SPI API Updates - SC12
Page 327 and 328:
● Interrupt_0x14_function_0x04:_I
Page 329 and 330:
DX Port number: 0 for EXT, 1 for CO
Page 331 and 332:
DX 0x08 Port number: 0 for EXT, 1 f
Page 333 and 334:
AH AL DX 0x0F Bit mask describing r
Page 335 and 336: ES:DI Pointer to user buffer. Retur
Page 337 and 338: Top of list Index page transmitter.
Page 339 and 340: DX 2: short break (1 frame) 3: extr
Page 341 and 342: Top of list Index page send queue.
Page 343 and 344: User specific TCPIP Device driver -
Page 345 and 346: Generic example: int huge myDevSend
Page 347 and 348: Implementation of this function is
Page 349 and 350: } } Related Topics Top of list Inde
Page 351 and 352: { result= Dev_Wait_DHCP_Complete(&m
Page 353 and 354: Index page Configuring the PPP Serv
Page 355 and 356: the call without waiting for the PP
Page 357 and 358: Top of list Index page Available Ex
Page 359 and 360: ● Interrupt_0xAB_function_0x07:_C
Page 361 and 362: Return Value Comments DX =0 success
Page 363 and 364: Top of list Index page CGI_FINDNEXT
Page 365 and 366: IPC@CHIP Documentation Index CGI AP
Page 367 and 368: Top of list Index page @CHIP V0.92
Page 369 and 370: IPC@CHIP Documentation Index Data S
Page 371 and 372: Comments typedef struct { //*******
Page 373 and 374: IPC@CHIP Documentation Index CGI AP
Page 375 and 376: CGI Examples Available - SC12 @CHIP
Page 377 and 378: The interrupt declaration will moti
Page 379 and 380: Interrupt 0xAE service 0x01: DRIVER
Page 381 and 382: Handle from ACCESS_TYPE call 0x02 R
Page 383 and 384: AH 0x15 Return Value Carry flag:0,
Page 385: Top of list Index page ACCESS_TYPE
Page 389 and 390: HW API handler latency RTX handler
Page 391 and 392: Scalable @CHIP-RTOS variants for th
Page 393 and 394: IPC@CHIP Documentation Index Progra
Page 395 and 396: IPC@CHIP Documentation Index Introd
Page 397 and 398: Top of list Index page TFTP server
Page 399 and 400: Top of list Index page Possible err
show all

IPC@CHIP Documentation - SC12 @CHIP-RTOS V1.10

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?