VCDS Release 11.11 PDF Manual Printing Instructions: - Ross-Tech

More documents

Recommendations

Info

VCDS – Options Screen – Section 30-A On this screen you can set a number of Options organized by tabbed sections that must be used the first time you run VCDS on a PC.
Port and Protocol Options Select Port Options Screen cont. – Section 30-B Set the COM Port to which you have connected the Interface Adapter. Serial Ports should be assigned to COM1 through COM4 (most often COM1 by default) while USB has only its eponymous choice. Make sure the ignition is turned on and the interface plugged into the vehicle, then click [Test] to see if VCDS can find the interface. See Getting Started (section 1 in this manual) for more information. The [LEDs] button causes the LED on the Interface to blink and may be useful for testing a port's outputs for troubleshooting certain connection issues. Protocol Options Start Baud is the first baud rate that VCDS will try when connecting to a controller. The current default value is 0. This means VCDS will determine the correct start baud on its own. With our current Interfaces, this field is unavailable. KW2 Delay has to do with the amount of time used during the initialization of a session between the PC and the car. The current default value is 30. Do not change this value from the default unless you are having difficulties communicating with a particular controller. Contact us for advice if you are. TST Addr. has to do with the packet addresses used by KWP-2000. The current default value is -1. Do not change this value from the default unless you are having difficulties communicating with a particular controller. Contact us for advice if you are. Debug Level controls how much debugging information VCDS records. A zero in this field (the default) means NO debug output will be generated whatsoever. This should decrease VCDS's susceptibility to interference by things like virus scanners (except when logging data). There should be no reason to set Debug to anything other than zero unless you are instructed to do so by Ross-Tech.
Page 1 and 2:
VCDS Release 11.11 PDF Manual Print
Page 3 and 4:
Disclaimer: All rights reserved, No
Page 5 and 6:
VCDS - Getting Started - Section 1-
Page 7 and 8:
Step #5 ► Getting Started - Secti
Page 9 and 10:
VCDS - Main Screen - Section 2-A Th
Page 11 and 12:
Auto Scan cont. - Section 3-B There
Page 13 and 14:
Auto-Scan cont. - Section 3-D The V
Page 15 and 16: VCDS - Open Controller- Section 5-A
Page 17 and 18: VCDS - Fault Codes - Section 6-A (V
Page 19 and 20: Fault Codes cont. - Section 6-C [Pr
Page 21 and 22: Measuring Blocks cont. - Section 7-
Page 23 and 24: Measuring Blocks cont. - Section 7-
Page 25 and 26: Data Logging cont. - Section 8-B Du
Page 27 and 28: VCDS - Single Reading- Section 9-A
Page 29 and 30: VCDS - View Readiness - Section 11-
Page 31 and 32: View Readiness cont. - Section 11-C
Page 33 and 34: VCDS - Advanced Measuring Values -
Page 35 and 36: VCDS - Acceleration Measurement - S
Page 37 and 38: VCDS - 7-digit PIN/SKC - Section 16
Page 39 and 40: Basic Settings cont. - Section 17-B
Page 41 and 42: Notes: Basic Settings cont. - Secti
Page 43 and 44: Output Tests cont. - Section 18-B O
Page 45 and 46: Output Tests cont. - Section 18-D M
Page 47 and 48: Recode cont. - Section 19-B A featu
Page 49 and 50: Recode cont. - Section 19-D Long Co
Page 51 and 52: Recode cont. - Section 19-F On some
Page 53 and 54: Adaptation / Long Adaptation cont.
Page 55 and 56: VCDS - Security Access Screen - Sec
Page 57 and 58: SRI Reset cont. - Section 22-B The
Page 59 and 60: Generic OBD2 cont. - Section 23-B I
Page 61 and 62: VCDS - Transport Mode - Section 25-
Page 63 and 64: VCDS - EDC-15-16 Mileage Checker -
Page 65: VCDS - Optical Bus Diagnostics - Se
Page 69 and 70: Options Screen cont. - Section 30-D
Page 71 and 72: License Info VCDS - About Screen -
Page 73 and 74: Quick Instructions cont: VC-Scope c
Page 75 and 76: Step by step: TDI Timing Checker co
show all

VCDS Release 11.11 PDF Manual Printing Instructions: - Ross-Tech

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?