ES7000 Model 7600R G2 Installation and User's Guide

More documents

Recommendations

Info

Safety Safety statements Important: Statement 1: Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document. For example, if a caution statement is labeled “Statement 1,” translations for that caution statement are in the Safety Information document under “Statement 1.” Be sure to read all caution and danger statements in this document before you perform the procedures. Read any additional safety information that comes with the server or optional device before you install the device. 1–2 3850 7273–001
DANGER Statement 2: Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect to properly wired outlets any equipment that will be attached to this product. • When possible, use one hand only to connect or disconnect signal cables. • Never turn on any equipment when there is evidence of fire, water, or structural damage. • Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. To Connect: 1. Turn everything OFF. 2. First, attach all cables to devices. 3. Attach signal cables to connectors. 4. Attach power cords to outlet. 5. Turn device ON. CAUTION: To Disconnect: 1. Turn everything OFF. 2. First, remove power cords from outlet. 3. Remove signal cables from connectors. 4. Remove all cables from devices. When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) Safety 3850 7273–001 1–3
Page 1 and 2: EnterpriseServer ES7000Model7600RG2
Page 3 and 4: Contents Section 1. Safety Safety s
Page 5 and 6: Section 4. Configuring the server C
Page 7 and 8: Tables 3-1. I/O-board jumpers . . .
Page 9: Section 1 Safety Before installing
Page 13 and 14: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5
Page 15 and 16: DANGER Statement 15: Overloading a
Page 17 and 18: Section 2 The ES7000 Model 7600R G2
Page 19 and 20: Documentation Updates This document
Page 21 and 22: eflections and other nearby noise s
Page 23 and 24: • Support for ServeRAID-M1015 SAS
Page 25 and 26: • Call Home Call Home is a Unisys
Page 27 and 28: • Advanced memory features: - Sin
Page 29 and 30: Front view The following illustrati
Page 31 and 32: To access the light path diagnostic
Page 33 and 34: Serial connector: Connect a 9-pin s
Page 35 and 36: Turning on the server The power-con
Page 37 and 38: Before you start the host server to
Page 39 and 40: Power supply: • One 675-watt (110
Page 41 and 42: • Hot-swap and redundant power su
Page 43 and 44: power LED. When the DC power LED is
Page 45 and 46: Section 3 Installing optional devic
Page 47 and 48: Orange on a component or an orange
Page 49 and 50: Backplane 2 (for HDD 4-7) Backplane
Page 51 and 52: I/O-board connectors Microprocessor
Page 53 and 54: Jumper number I/O-board LEDs Wake o
Page 55 and 56: - Boot Failed. Hard Disk 0 - Broadc
Page 57 and 58: Handling static-sensitive devices A
Page 59 and 60: DVD signal cable Removing the top c
Page 61 and 62:
5. Slide the blue latches on the to
Page 63 and 64:
Removing the bezel Note: You do not
Page 65 and 66:
Adapter Pin Pin hole Adapter retent
Page 67 and 68:
5. Push the adapter retention latch
Page 69 and 70:
If you have other devices to instal
Page 71 and 72:
Installing a 2.5-inch hard disk dri
Page 73 and 74:
13. Orient and install the new back
Page 75 and 76:
19. Install the ServeRAID adapter o
Page 77 and 78:
7. Remove the backplane filler from
Page 79 and 80:
4. Pull the lever to slide the driv
Page 81 and 82:
If you have other devices to instal
Page 83 and 84:
• Install the DIMMs on each memor
Page 85 and 86:
Table 3-3. Memory-card installation
Page 87 and 88:
To install a memory card, complete
Page 89 and 90:
8. Turn the DIMM so that the DIMM k
Page 91 and 92:
4. Slide the top cover forward; the
Page 93 and 94:
Removing the Memory Expansion Modul
Page 95 and 96:
• The Memory Expansion Module pro
Page 97 and 98:
Module is attached to a host server
Page 99 and 100:
Installing optional devices 6. Touc
Page 101 and 102:
CAUTION: Installing optional device
Page 103 and 104:
Replacing the Memory Expansion Modu
Page 105 and 106:
Updating the Memory Expansion Modul
Page 107 and 108:
Section 4 Configuring the server Th
Page 109 and 110:
1. Turn on the server. Note: The po
Page 111 and 112:
Select this choice to view or chang
Page 113 and 114:
Passwords This choice is on the ful
Page 115 and 116:
Using the Boot Selection Menu progr
Page 117 and 118:
available space to allocate from th
Page 119 and 120:
ES7/7600R G2 Intel PRO/1000 PT Dual
Page 121 and 122:
You are directed to change CD-ROMs
Page 123 and 124:
Updating device drivers and PCI car
Page 125 and 126:
Installation procedure Complete the
Page 127 and 128:
Note: If you do not remove the medi
Page 129 and 130:
Preparing to use a Xen Virtual Mach
Page 131 and 132:
Preinstallation notes • This inst
Page 133 and 134:
When the initial installation phase
Page 135 and 136:
If you want to use the server as a
Page 137 and 138:
3. Click Power Up/Down to start the
Page 139 and 140:
Installing VMware Patches Updates a
Page 141 and 142:
To add the USB flash device to the
Page 143 and 144:
Enabling the Broadcom Gigabit Ether
Page 145 and 146:
Section 5 Configuring Call Home Cal
Page 147 and 148:
3. Define the name of your SMTP ser
Page 149 and 150:
c. Make the following changes: •
Page 151 and 152:
Appendix A Services and Support Thi
Page 153 and 154:
Service Task Responsibility Billabl
Page 155 and 156:
Appendix B Notices Important notes
Page 157 and 158:
easonable protection against harmfu
Page 159 and 160:
Japan Electronics and Information T
Page 161 and 162:
Index A AC power LED, 2-18 adapter
Page 163 and 164:
DC power, 2-18 error, 3-3 memory, 3
Page 166:
© Portions copyright Unisys Corpor
show all

ES7000 Model 7600R G2 Installation and User's Guide

Create successful ePaper yourself

Delete template?

Save as template?