ES7000 Model 7600R G2 Installation and User's Guide

More documents

Recommendations

Info

The ES7000 Model 7600R G2 Server Electrical input: • Sine-wave input (50 - 60 Hz) required • Input voltage low range: - Minimum: 100 VAC - Maximum: 127 VAC • Input voltage high range: - Minimum: 200 VAC - Maximum: 240 VAC • Approximate input kilovolt-amperes (kVA): - Minimum: 0.20 kVA - Typical: 1.12 kVA - Maximum: 1.95 kVA (110 VAC) - Maximum: 2.17 kVA (220 VAC) What your server offers The server uses the following features and technologies: • UEFI-compliant server firmware Server firmware offers several features, including Unified Extensible Firmware Interface (UEFI) 2.1 compliance; enhanced reliability, availability, and serviceability (RAS) capabilities; and basic input/output system (BIOS) compatibility support. UEFI replaces the BIOS and defines a standard interface between the operating system, platform firmware, and external devices. UEFI-compliant servers are capable of booting UEFI-compliant operating systems, BIOS-based operating systems, and BIOS-based adapters as well as UEFI-compliant adapters. Note: The server does not support DOS. • Integrated management module The integrated management module (IMM) combines service processor functions, video controller, and remote presence and blue-screen capture features in a single chip. The IMM provides advanced service processor control, monitoring, and alerting function. If an environmental condition exceeds a threshold or if a system component fails, the IMM lights LEDs to help you diagnose the problem, records the error in the IMM event log, and alerts you to the problem. Optionally, the IMM also provides a virtual presence capability for remote server management capabilities. The IMM provides remote server management through industry-standard interfaces: - Intelligent Platform Management Interface (IPMI) version 2.0 - Simple Network Management Protocol (SNMP) version 3 - Common Information Model (CIM) - Web browser (For more information, see Using the Integrated Management Module.) 2–8 3850 7273–001
• Call Home Call Home is a Unisys software tool that monitors the server for hardware error events. When a hardware error is located, it automatically submits a service request packet through e-mail to the Unisys client support center. These packets contain information on system or controller errors that are determined according to a predefined set of conditions. For information on setting up Call Home through use of the Integrated Management Module, see Section 5, Configuring Call Home. • Large system-memory capacity The server supports up to 1 TB of system memory. The memory controller supports error correcting code (ECC) for up to 64 industry-standard PC3-10600, 1.8 V, 240-pin, registered, double-data-rate (DDR) III, synchronous dynamic random access memory (SDRAM) dual inline memory modules (DIMMs). The optional 32-DIMM Memory Expansion Module is available for purchase and provides up to 512 GB of additional memory. For more information about the Memory Expansion Module, see Memory Expansion Module. • Memory ProteXion The Memory ProteXion feature provides the equivalent of a hot-spare drive in a RAID array. It is based in the memory controller, and it enables the server to sense when a chip on a DIMM has failed and to route the data around the failed chip. • Integrated network support The server comes with an integrated Broadcom 5709 dual Gigabit Ethernet controller, which supports connection to a 10 Mbps, 100 Mbps, or 1000 Mbps network. For more information, see Configuring the Broadcom Gigabit Ethernet controller. • Integrated Trusted Platform Module (TPM) This integrated security chip performs cryptographic functions and stores private and public secure keys. It provides the hardware support for the Trusted Computing Group (TCG) specification. You can download the software to support the TCG specification, when the software is available. • Large data-storage capacity and hot-swap capability The server supports up to eight 1-inch (26 mm) slim-high, 2.5-inch hot-swap hard disk drives that are connected to two SAS backplanes. With the hot-swap feature, you can add, remove, and replace hard disk drives without turning off the server. For more information, see Installing a hot-swap hard disk drive. • Light path diagnostics Light path diagnostics provides LEDs to help you diagnose problems. For more information, see the section about light path diagnostics in the Problem Determination and Service Guide. • PCI Express 2.0 adapter capabilities The ES7000 Model 7600R G2 Server The server has six slots for PCI Express 2.0 x8 adapters and one slot for PCI Express x16 adapters. For more information, see Installing a PCI Express adapter. • Dynamic System Analysis (DSA) Preboot diagnostic programs 3850 7273–001 2–9
Page 1 and 2: EnterpriseServer ES7000Model7600RG2
Page 3 and 4: Contents Section 1. Safety Safety s
Page 5 and 6: Section 4. Configuring the server C
Page 7 and 8: Tables 3-1. I/O-board jumpers . . .
Page 9 and 10: Section 1 Safety Before installing
Page 11 and 12: DANGER Statement 2: Electrical curr
Page 13 and 14: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5
Page 15 and 16: DANGER Statement 15: Overloading a
Page 17 and 18: Section 2 The ES7000 Model 7600R G2
Page 19 and 20: Documentation Updates This document
Page 21 and 22: eflections and other nearby noise s
Page 23: • Support for ServeRAID-M1015 SAS
Page 27 and 28: • Advanced memory features: - Sin
Page 29 and 30: Front view The following illustrati
Page 31 and 32: To access the light path diagnostic
Page 33 and 34: Serial connector: Connect a 9-pin s
Page 35 and 36: Turning on the server The power-con
Page 37 and 38: Before you start the host server to
Page 39 and 40: Power supply: • One 675-watt (110
Page 41 and 42: • Hot-swap and redundant power su
Page 43 and 44: power LED. When the DC power LED is
Page 45 and 46: Section 3 Installing optional devic
Page 47 and 48: Orange on a component or an orange
Page 49 and 50: Backplane 2 (for HDD 4-7) Backplane
Page 51 and 52: I/O-board connectors Microprocessor
Page 53 and 54: Jumper number I/O-board LEDs Wake o
Page 55 and 56: - Boot Failed. Hard Disk 0 - Broadc
Page 57 and 58: Handling static-sensitive devices A
Page 59 and 60: DVD signal cable Removing the top c
Page 61 and 62: 5. Slide the blue latches on the to
Page 63 and 64: Removing the bezel Note: You do not
Page 65 and 66: Adapter Pin Pin hole Adapter retent
Page 67 and 68: 5. Push the adapter retention latch
Page 69 and 70: If you have other devices to instal
Page 71 and 72: Installing a 2.5-inch hard disk dri
Page 73 and 74: 13. Orient and install the new back
Page 75 and 76:
19. Install the ServeRAID adapter o
Page 77 and 78:
7. Remove the backplane filler from
Page 79 and 80:
4. Pull the lever to slide the driv
Page 81 and 82:
If you have other devices to instal
Page 83 and 84:
• Install the DIMMs on each memor
Page 85 and 86:
Table 3-3. Memory-card installation
Page 87 and 88:
To install a memory card, complete
Page 89 and 90:
8. Turn the DIMM so that the DIMM k
Page 91 and 92:
4. Slide the top cover forward; the
Page 93 and 94:
Removing the Memory Expansion Modul
Page 95 and 96:
• The Memory Expansion Module pro
Page 97 and 98:
Module is attached to a host server
Page 99 and 100:
Installing optional devices 6. Touc
Page 101 and 102:
CAUTION: Installing optional device
Page 103 and 104:
Replacing the Memory Expansion Modu
Page 105 and 106:
Updating the Memory Expansion Modul
Page 107 and 108:
Section 4 Configuring the server Th
Page 109 and 110:
1. Turn on the server. Note: The po
Page 111 and 112:
Select this choice to view or chang
Page 113 and 114:
Passwords This choice is on the ful
Page 115 and 116:
Using the Boot Selection Menu progr
Page 117 and 118:
available space to allocate from th
Page 119 and 120:
ES7/7600R G2 Intel PRO/1000 PT Dual
Page 121 and 122:
You are directed to change CD-ROMs
Page 123 and 124:
Updating device drivers and PCI car
Page 125 and 126:
Installation procedure Complete the
Page 127 and 128:
Note: If you do not remove the medi
Page 129 and 130:
Preparing to use a Xen Virtual Mach
Page 131 and 132:
Preinstallation notes • This inst
Page 133 and 134:
When the initial installation phase
Page 135 and 136:
If you want to use the server as a
Page 137 and 138:
3. Click Power Up/Down to start the
Page 139 and 140:
Installing VMware Patches Updates a
Page 141 and 142:
To add the USB flash device to the
Page 143 and 144:
Enabling the Broadcom Gigabit Ether
Page 145 and 146:
Section 5 Configuring Call Home Cal
Page 147 and 148:
3. Define the name of your SMTP ser
Page 149 and 150:
c. Make the following changes: •
Page 151 and 152:
Appendix A Services and Support Thi
Page 153 and 154:
Service Task Responsibility Billabl
Page 155 and 156:
Appendix B Notices Important notes
Page 157 and 158:
easonable protection against harmfu
Page 159 and 160:
Japan Electronics and Information T
Page 161 and 162:
Index A AC power LED, 2-18 adapter
Page 163 and 164:
DC power, 2-18 error, 3-3 memory, 3
Page 166:
© Portions copyright Unisys Corpor
show all

ES7000 Model 7600R G2 Installation and User's Guide

Create successful ePaper yourself

Delete template?

Save as template?