ES7000 Model 7600R G2 Installation and User's Guide

More documents

Recommendations

Info

Installing optional devices Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the server, open or close a latch, <strong>and</strong> so on. 3–2 3850 7273–001
Orange on a component or an orange label on or near a component indicates that the component can be hot-swapped, which means that if the server <strong>and</strong> operating system support hot-swap capability, you can remove or install the component while the server is running. (Orange can also indicate touch points on hot-swap components.) See the instructions for removing or installing a specific hot-swap component for any additional procedures that you might have to perform before you remove or install the component. Memory-card DIMM connectors The following illustration shows the DIMM connectors on a memory card. Memory-card LEDs The following illustration shows the LEDs on a memory card. Installing optional devices DIMM 1 DIMM 2 DIMM 3 DIMM 4 DIMM 5 DIMM 6 DIMM 7 DIMM 8 3850 7273–001 3–3
Page 1 and 2: EnterpriseServer ES7000Model7600RG2
Page 3 and 4: Contents Section 1. Safety Safety s
Page 5 and 6: Section 4. Configuring the server C
Page 7 and 8: Tables 3-1. I/O-board jumpers . . .
Page 9 and 10: Section 1 Safety Before installing
Page 11 and 12: DANGER Statement 2: Electrical curr
Page 13 and 14: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5
Page 15 and 16: DANGER Statement 15: Overloading a
Page 17 and 18: Section 2 The ES7000 Model 7600R G2
Page 19 and 20: Documentation Updates This document
Page 21 and 22: eflections and other nearby noise s
Page 23 and 24: • Support for ServeRAID-M1015 SAS
Page 25 and 26: • Call Home Call Home is a Unisys
Page 27 and 28: • Advanced memory features: - Sin
Page 29 and 30: Front view The following illustrati
Page 31 and 32: To access the light path diagnostic
Page 33 and 34: Serial connector: Connect a 9-pin s
Page 35 and 36: Turning on the server The power-con
Page 37 and 38: Before you start the host server to
Page 39 and 40: Power supply: • One 675-watt (110
Page 41 and 42: • Hot-swap and redundant power su
Page 43 and 44: power LED. When the DC power LED is
Page 45: Section 3 Installing optional devic
Page 49 and 50: Backplane 2 (for HDD 4-7) Backplane
Page 51 and 52: I/O-board connectors Microprocessor
Page 53 and 54: Jumper number I/O-board LEDs Wake o
Page 55 and 56: - Boot Failed. Hard Disk 0 - Broadc
Page 57 and 58: Handling static-sensitive devices A
Page 59 and 60: DVD signal cable Removing the top c
Page 61 and 62: 5. Slide the blue latches on the to
Page 63 and 64: Removing the bezel Note: You do not
Page 65 and 66: Adapter Pin Pin hole Adapter retent
Page 67 and 68: 5. Push the adapter retention latch
Page 69 and 70: If you have other devices to instal
Page 71 and 72: Installing a 2.5-inch hard disk dri
Page 73 and 74: 13. Orient and install the new back
Page 75 and 76: 19. Install the ServeRAID adapter o
Page 77 and 78: 7. Remove the backplane filler from
Page 79 and 80: 4. Pull the lever to slide the driv
Page 81 and 82: If you have other devices to instal
Page 83 and 84: • Install the DIMMs on each memor
Page 85 and 86: Table 3-3. Memory-card installation
Page 87 and 88: To install a memory card, complete
Page 89 and 90: 8. Turn the DIMM so that the DIMM k
Page 91 and 92: 4. Slide the top cover forward; the
Page 93 and 94: Removing the Memory Expansion Modul
Page 95 and 96: • The Memory Expansion Module pro
Page 97 and 98:
Module is attached to a host server
Page 99 and 100:
Installing optional devices 6. Touc
Page 101 and 102:
CAUTION: Installing optional device
Page 103 and 104:
Replacing the Memory Expansion Modu
Page 105 and 106:
Updating the Memory Expansion Modul
Page 107 and 108:
Section 4 Configuring the server Th
Page 109 and 110:
1. Turn on the server. Note: The po
Page 111 and 112:
Select this choice to view or chang
Page 113 and 114:
Passwords This choice is on the ful
Page 115 and 116:
Using the Boot Selection Menu progr
Page 117 and 118:
available space to allocate from th
Page 119 and 120:
ES7/7600R G2 Intel PRO/1000 PT Dual
Page 121 and 122:
You are directed to change CD-ROMs
Page 123 and 124:
Updating device drivers and PCI car
Page 125 and 126:
Installation procedure Complete the
Page 127 and 128:
Note: If you do not remove the medi
Page 129 and 130:
Preparing to use a Xen Virtual Mach
Page 131 and 132:
Preinstallation notes • This inst
Page 133 and 134:
When the initial installation phase
Page 135 and 136:
If you want to use the server as a
Page 137 and 138:
3. Click Power Up/Down to start the
Page 139 and 140:
Installing VMware Patches Updates a
Page 141 and 142:
To add the USB flash device to the
Page 143 and 144:
Enabling the Broadcom Gigabit Ether
Page 145 and 146:
Section 5 Configuring Call Home Cal
Page 147 and 148:
3. Define the name of your SMTP ser
Page 149 and 150:
c. Make the following changes: •
Page 151 and 152:
Appendix A Services and Support Thi
Page 153 and 154:
Service Task Responsibility Billabl
Page 155 and 156:
Appendix B Notices Important notes
Page 157 and 158:
easonable protection against harmfu
Page 159 and 160:
Japan Electronics and Information T
Page 161 and 162:
Index A AC power LED, 2-18 adapter
Page 163 and 164:
DC power, 2-18 error, 3-3 memory, 3
Page 166:
© Portions copyright Unisys Corpor
show all

ES7000 Model 7600R G2 Installation and User's Guide

Create successful ePaper yourself

Delete template?

Save as template?