Create OMR Job - Pitney Bowes Canada

More documents

Recommendations

Info

Operation Filling the Sealer When the sealer unit needs refilling, the Add Fluid symbol will flash in the display. Add Pitney Bowes EZ Seal® solution or water in the following way: Note: EZ Seal® solution is recommended to minimize growth of algae and scale build-up. Hinge open the Water Bottle Cover located at the rear right hand side of the machine. Remove the bottle Fill the bottle up to the level indicated. Replace the water bottle and close the cover. If the sealer unit has been allowed to completely empty, you should allow time for water to soak through the sealer mechanism. 2-8
Programming Features At A Glance 2-9 Operation The DI400 has the ability to be programmed by the operator with up to 20 jobs which can be recalled at the touch of a button. The table below shows the other functions and settings that are available. Function Sheet Feeder 1 On (with double detect), On (without double detect), Off, or Manual Feed, Select Feed (with double detect), or Select Feed (without double detect) Insert Feeder On (with double detect), On (without double detect), Off, Select Feed (with double detect), or Select Feed (without double detect) Sheet Feeder 2 On (with double detect), On (without double detect), Off, Select Feed (with double detect), or Select Feed (without double detect) Accumul Mode Off or On (with 2, 3,4, or 5 pages) OMR Mode Off, On, OMR + Sequence, OMR + Select Feed and Sequence, OMR + Select Feed Mode Insertion Mode, Fold Only Mode Number of Jobs Up to 20; each job can be programmed by the operator Fold Type C - Letter, Z - Accordion, Double or Single Paper Length any within machine specification limits Fold A any within machine/fold specification limits Fold B any within machine/fold specification limits Envelope Depth any within machine specification limits Envelope Stop 1 to 5 Possible Settings Batch Mode Off or On (from 50 to 99)
Page 1 and 2: SV40191-OG Rev. A DI400 FastPac Ins
Page 3 and 4: ABOUT THIS GUIDE iii Contents This
Page 5 and 6: 4. WHAT IS OMR (OPTICAL MARK RECOGN
Page 7 and 8: 6. REFERENCE vii Contents Changing
Page 9 and 10: 1. INTRODUCTION To the Operator 1-1
Page 11 and 12: Machine Identification 5 2 1-3 Intr
Page 13 and 14: 1-5 Introduction 11 Sealer Water Bo
Page 15 and 16: Display Symbols . . 3 . . Used on s
Page 17 and 18: 2. OPERATION 2-1 Operation This sec
Page 19 and 20: Start Machine Operation 2-3 Operati
Page 21 and 22: Setting the Envelope Feeder 1. Adju
Page 23: 4. Set the separator shield to the
Page 27 and 28: 3. CREATE NON-OMR JOB Create Non-OM
Page 29 and 30: Create Non-OMR Job Open hinged cove
Page 31 and 32: Create Non-OMR Job Flowchart for No
Page 33 and 34: Create Non-OMR Job Setting Sheet Fe
Page 35 and 36: Create Non-OMR Job Setting Insert F
Page 37 and 38: Fold A Select the size of the first
Page 39 and 40: Create Non-OMR Job Batch Mode The b
Page 41 and 42: Changing an existing job Create Non
Page 43 and 44: 4. WHAT IS OMR? 4-1 What is OMR? DI
Page 45 and 46: 4-3 What is OMR? How are OMR Marks
Page 47 and 48: 4-5 What is OMR? What OMR Marks are
Page 49 and 50: Overview of Group 2 OMR Marks Group
Page 51 and 52: OMR Group 1 and 3 Marks (Enhanced L
Page 53 and 54: 4-11 What is OMR? While the feeders
Page 55 and 56: 4-13 What is OMR? Example of Group
Page 57 and 58: 4-15 What is OMR? • Selective Fee
Page 59 and 60: OMR Group 3 Marks (“Sequence”)
Page 61 and 62: 4-19 What is OMR? Example of Group
Page 63 and 64: View of Mark Order and Position on
Page 65 and 66: 4-23 What is OMR? View of OMR Mark
Page 67 and 68: 4-25 What is OMR? OMR Printing/Feed
Page 69 and 70: 5. CREATE OMR JOB 5-1 Create OMR Jo
Page 71 and 72: 5-3 Create OMR Job Selecting the OM
Page 73 and 74: 5-5 Create OMR Job Flowchart for OM
Page 75 and 76:
5-7 Create OMR Job Setting the Main
Page 77 and 78:
Setting Insert Feeder Select whethe
Page 79 and 80:
Fold A Select the size of the first
Page 81 and 82:
5-13 Create OMR Job Batch Mode The
Page 83 and 84:
5-15 Create OMR Job Fold a sheet of
Page 85 and 86:
5-17 Create OMR Job Loading the Mat
Page 87 and 88:
Changing an existing job 5-19 Creat
Page 89 and 90:
6. REFERENCE Changing the Display L
Page 91 and 92:
Removal & Replacement of the Insert
Page 93 and 94:
Changing the Sealer Unit Felts 6-5
Page 95 and 96:
7. Fit the four new felts into the
Page 97 and 98:
6-9 Reference SYMPTOM POSSIBLE REME
Page 99 and 100:
6-11 Reference SYMPTOM POSSIBLE REM
Page 101 and 102:
Error Recovery for Empty Feeders Er
Page 103 and 104:
MESSAGE ACTION 6-15 Reference CLEAR
Page 105 and 106:
MESSAGE ACTION 6-17 Reference STREA
Page 107 and 108:
MESSAGE ACTION 6-19 Reference OMR:S
Page 109 and 110:
6-21 Reference Sealer The machine c
Page 111 and 112:
Machine Specifications Physical Dim
Page 113 and 114:
Appendix A -Training Checklist Use
Page 115 and 116:
I-i Index A Accumulation Mode 3-5 A
Page 117 and 118:
Insertion Mode 3-9 I-iii Index J Ja
Page 119 and 120:
I-v Index Scanner, OMR Adjustment o
show all

Create OMR Job - Pitney Bowes Canada

Create successful ePaper yourself

Delete template?

Save as template?