Create OMR Job - Pitney Bowes Canada

More documents

Recommendations

Info

Create Non-OMR Job Fold Type Select the type of fold. Press Change (+/-) until you see the option you want: C - Letter Folds your sheet into a standard ‘C’ or letter fold. Z - Accordion Folds your sheet into a ‘Z’ or accordion fold. Double Folds your sheet in half and then in half again. Single Folds your sheet once. When the fold type is set as required, press Next ( ) to advance to the next setting… 3-6
Create Non-OMR Job Setting Sheet Feeder 1 (Upper Feeder) Select whether you want to use sheet feeder 1 and, if so, how it will be used. Press Change (+/-) until you see the option you want: On Double Detect Feeder on with the double detector operating. (The double detector stops the machine if more than one sheet simultaneously feeds from the feeder). On Feeder on without the double detector. Manual Feed Allows you to manually feed collated sets (see notes below). Off Feeder turned off for this job. Switchable: On Feed will initially be from Sheet Switchable: On Dble Detect Feeder 1. When the feeder is empty, the machine will automatically switch to feeding from sheet feeder 2. When a trial piece is requested, both feeders must be loaded as a trial piece will be fed from each feeder Notes About Manual Feed: 1. The manual feed setting allows stapled sets of up to 5 sheets of 20/24 lb (to a maximum of 120 lbs per set) to be run. The maximum compressed thickness of the set after folding must not exceed 2mm. The machine will wait for manual insertion of each set into sheet feeder 1 after which it will fold and insert the set automatically. 2. When running manual feed mode, sheet feeder 2 becomes inoperable 3-7
Page 1 and 2: SV40191-OG Rev. A DI400 FastPac Ins
Page 3 and 4: ABOUT THIS GUIDE iii Contents This
Page 5 and 6: 4. WHAT IS OMR (OPTICAL MARK RECOGN
Page 7 and 8: 6. REFERENCE vii Contents Changing
Page 9 and 10: 1. INTRODUCTION To the Operator 1-1
Page 11 and 12: Machine Identification 5 2 1-3 Intr
Page 13 and 14: 1-5 Introduction 11 Sealer Water Bo
Page 15 and 16: Display Symbols . . 3 . . Used on s
Page 17 and 18: 2. OPERATION 2-1 Operation This sec
Page 19 and 20: Start Machine Operation 2-3 Operati
Page 21 and 22: Setting the Envelope Feeder 1. Adju
Page 23 and 24: 4. Set the separator shield to the
Page 25 and 26: Programming Features At A Glance 2-
Page 27 and 28: 3. CREATE NON-OMR JOB Create Non-OM
Page 29 and 30: Create Non-OMR Job Open hinged cove
Page 31: Create Non-OMR Job Flowchart for No
Page 35 and 36: Create Non-OMR Job Setting Insert F
Page 37 and 38: Fold A Select the size of the first
Page 39 and 40: Create Non-OMR Job Batch Mode The b
Page 41 and 42: Changing an existing job Create Non
Page 43 and 44: 4. WHAT IS OMR? 4-1 What is OMR? DI
Page 45 and 46: 4-3 What is OMR? How are OMR Marks
Page 47 and 48: 4-5 What is OMR? What OMR Marks are
Page 49 and 50: Overview of Group 2 OMR Marks Group
Page 51 and 52: OMR Group 1 and 3 Marks (Enhanced L
Page 53 and 54: 4-11 What is OMR? While the feeders
Page 55 and 56: 4-13 What is OMR? Example of Group
Page 57 and 58: 4-15 What is OMR? • Selective Fee
Page 59 and 60: OMR Group 3 Marks (“Sequence”)
Page 61 and 62: 4-19 What is OMR? Example of Group
Page 63 and 64: View of Mark Order and Position on
Page 65 and 66: 4-23 What is OMR? View of OMR Mark
Page 67 and 68: 4-25 What is OMR? OMR Printing/Feed
Page 69 and 70: 5. CREATE OMR JOB 5-1 Create OMR Jo
Page 71 and 72: 5-3 Create OMR Job Selecting the OM
Page 73 and 74: 5-5 Create OMR Job Flowchart for OM
Page 75 and 76: 5-7 Create OMR Job Setting the Main
Page 77 and 78: Setting Insert Feeder Select whethe
Page 79 and 80: Fold A Select the size of the first
Page 81 and 82: 5-13 Create OMR Job Batch Mode The
Page 83 and 84:
5-15 Create OMR Job Fold a sheet of
Page 85 and 86:
5-17 Create OMR Job Loading the Mat
Page 87 and 88:
Changing an existing job 5-19 Creat
Page 89 and 90:
6. REFERENCE Changing the Display L
Page 91 and 92:
Removal & Replacement of the Insert
Page 93 and 94:
Changing the Sealer Unit Felts 6-5
Page 95 and 96:
7. Fit the four new felts into the
Page 97 and 98:
6-9 Reference SYMPTOM POSSIBLE REME
Page 99 and 100:
6-11 Reference SYMPTOM POSSIBLE REM
Page 101 and 102:
Error Recovery for Empty Feeders Er
Page 103 and 104:
MESSAGE ACTION 6-15 Reference CLEAR
Page 105 and 106:
MESSAGE ACTION 6-17 Reference STREA
Page 107 and 108:
MESSAGE ACTION 6-19 Reference OMR:S
Page 109 and 110:
6-21 Reference Sealer The machine c
Page 111 and 112:
Machine Specifications Physical Dim
Page 113 and 114:
Appendix A -Training Checklist Use
Page 115 and 116:
I-i Index A Accumulation Mode 3-5 A
Page 117 and 118:
Insertion Mode 3-9 I-iii Index J Ja
Page 119 and 120:
I-v Index Scanner, OMR Adjustment o
show all

Create OMR Job - Pitney Bowes Canada

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?