User Guide

More documents

Recommendations

Info

OSMOMAT 3000 Safety 2.2 Intended use Intended use 2.3 Additional hazards 2.3.1 Hazards due to electrical current Electrical current 14 Version 1.02 04/24/2013 The OSMOMAT 3000 device is a non-invasive in-vitro diagnostic product used to determine the osmolality of aqueous solutions. Only use the device to measure aqueous solutions. Never measure organic, saturated, or highly viscous solutions. Never administer measured samples to humans by infusion or injection. Never use calibration standards as cleaning solutions, e.g. for contact lenses. Only use accessories and consumables supplied by Gonotec GmbH for measurements. Accessories and consumables on page 24 DANGER! Risk of death due to electrical current on device! Class I devices must be connected to a power socket with protective ground wire. If the power or device connector is used as a separation device, the connector must be easily accessible at all times. Remove the power plug from the power socket to safely disconnect the device from mains voltage. Contact with energized parts of the device results in immediate risk of death due to electric shock. Damage to the insulation of individual components can cause risk of death. - Only have qualified personnel perform repair and maintenance work on the device. - If the insulation is damaged, immediately disconnect the power plug and schedule a repair. - Always route the power cord so it is not subject to stress and cannot be bent, pinched, or rolled over and is not exposed to liquids or heat. - Keep energized parts away from liquids. Otherwise, shorts may occur.
2.3.2 Risk of infection Risk of infection 2.3.3 Risk of injury Risk of injury OSMOMAT 3000 Safety WARNING! Risk of infection due to sample residue and in case of inadequate hygiene, disinfectant cleaning, and sterilization procedures! Exposure to sample residue in non-cleaned, nonsterilized, or non-disinfected components results in an elevated risk of infection. - Wear lab gloves during any kind of work. - Observe all local regulations regarding hygiene, disinfectant cleaning, and sterilization. We recommend using detergents such as Mikrozid ® AF Liquid, Bacillol ® plus 3%, or Korsolex ® plus 4% commonly found in clinical-chemical labs to clean and decontaminate the device. CAUTION! Risk of injury from initiation needle! When installing and removing the initiation needle and the thermistor probe, the tip of the initiation needle is exposed. Movement of the initiation needle can cause needle puncture injuries. - Always keep your hands and fingers clear from the area underneath the initiation needle. Version 1.02 04/24/2013 15
Page 1 and 2: 2/12/2013 User Guide OSMOMAT 3000 V
Page 3 and 4: OSMOMAT 3000 Overview of the OSMOMA
Page 5 and 6: Table of Contents OSMOMAT 3000 Over
Page 7 and 8: OSMOMAT 3000 Overview of the OSMOMA
Page 9 and 10: Device, rear Fig. 2: Device overvie
Page 11 and 12: Accessories Fig. 4: Overview of acc
Page 13: Special safety notices Safety notic
Page 17 and 18: 2.3.5 Reproducibility of the measur
Page 19 and 20: Inventory OSMOMAT 3000 Safety The o
Page 21 and 22: 2.6 Personal safety gear OSMOMAT 30
Page 23 and 24: Device, rear Fig. 6: Device overvie
Page 25 and 26: Accessories Fig. 8: Overview of acc
Page 27 and 28: 3.3 Measurement equipment Fig. 9: O
Page 29 and 30: Thermistor probe Fig. 11: Thermisto
Page 31 and 32: Enter values Fig. 13: Enter values
Page 33 and 34: 3.6 Connections and interfaces Fig.
Page 35 and 36: 3.6.2 Transfer protocol Output form
Page 37 and 38: 4.1 Packaging About the packaging H
Page 39 and 40: 4.2 Device storage 4.3 Unpack devic
Page 41 and 42: 5.2 Install device Fig. 21: Fan out
Page 43 and 44: 6 Setup Check printer (Option D) Ch
Page 45 and 46: Select calibration standards Fig. 2
Page 47 and 48: 7.1 Power up device Fig. 31: Power
Page 49 and 50: Fig. 33: Start menu Fig. 34: Ice fo
Page 51 and 52: Fig. 40: Move elevator down Fig. 41
Page 53 and 54: Fig. 45: Ice formation Fig. 46: Cal
Page 55 and 56: Fig. 52: Clean thermistor probe 12.
Page 57 and 58: Fig. 53: Clean thermistor probe Fig
Page 59 and 60: Calibrate device using calibration
Page 61 and 62: Fig. 63: Second calibration standar
Page 63 and 64: Configure screen saver Fig. 68: Con
Page 65 and 66:
7.6 Power down device Fig. 72: Powe
Page 67 and 68:
8.2 Notes regarding errors Fig. 75:
Page 69 and 70:
Measurement procedure takes longer
Page 71 and 72:
Device cannot be powered up Power s
Page 73 and 74:
Fig. 77: Remove mounting screw Fig.
Page 75 and 76:
Check free movement of initiation n
Page 77 and 78:
Fig. 86: Move elevator down Fig. 87
Page 79 and 80:
Fig. 93: Remove mounting plate 1 Mo
Page 81 and 82:
Fig. 99: Elevator cover with correc
Page 83 and 84:
8.4.3 Replace fine-wire fuses Fig.
Page 85 and 86:
Fig. 108: Pull out printer Fig. 109
Page 87 and 88:
Fig. 114: Pull out printer Fig. 115
Page 89 and 90:
9.1 Service table OSMOMAT 3000 Serv
Page 91 and 92:
Fig. 121: Remove mounting screws Fi
Page 93 and 94:
Install device front panel Fig. 127
Page 95 and 96:
Fig. 131: Lubricate elevator guide
Page 97 and 98:
9.5 Check reproducibility of measur
Page 99 and 100:
11 Specifications 11.1 Dimensions 1
Page 101 and 102:
OSMOMAT 3000 Specifications Power c
Page 103 and 104:
12 Index 2 2-point calibration ....
Page 105 and 106:
T Temperature sensor Replace ......
Page 107 and 108:
Fig. 138: "Safe Transport" menu Fig
Page 109 and 110:
Classification of the IVD OSMOMAT 3
Page 111:
Before Calling Gonotec Fig. 141: Co
show all

User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?