- Page 1: 2/12/2013 User Guide OSMOMAT 3000 V
- Page 5 and 6: Table of Contents OSMOMAT 3000 Over
- Page 7 and 8: OSMOMAT 3000 Overview of the OSMOMA
- Page 9 and 10: Device, rear Fig. 2: Device overvie
- Page 11 and 12: Accessories Fig. 4: Overview of acc
- Page 13 and 14: Special safety notices Safety notic
- Page 15 and 16: 2.3.2 Risk of infection Risk of inf
- Page 17 and 18: 2.3.5 Reproducibility of the measur
- Page 19 and 20: Inventory OSMOMAT 3000 Safety The o
- Page 21 and 22: 2.6 Personal safety gear OSMOMAT 30
- Page 23 and 24: Device, rear Fig. 6: Device overvie
- Page 25 and 26: Accessories Fig. 8: Overview of acc
- Page 27 and 28: 3.3 Measurement equipment Fig. 9: O
- Page 29 and 30: Thermistor probe Fig. 11: Thermisto
- Page 31 and 32: Enter values Fig. 13: Enter values
- Page 33 and 34: 3.6 Connections and interfaces Fig.
- Page 35 and 36: 3.6.2 Transfer protocol Output form
- Page 37 and 38: 4.1 Packaging About the packaging H
- Page 39 and 40: 4.2 Device storage 4.3 Unpack devic
- Page 41 and 42: 5.2 Install device Fig. 21: Fan out
- Page 43 and 44: 6 Setup Check printer (Option D) Ch
- Page 45 and 46: Select calibration standards Fig. 2
- Page 47 and 48: 7.1 Power up device Fig. 31: Power
- Page 49 and 50: Fig. 33: Start menu Fig. 34: Ice fo
- Page 51 and 52: Fig. 40: Move elevator down Fig. 41
- Page 53 and 54:
Fig. 45: Ice formation Fig. 46: Cal
- Page 55 and 56:
Fig. 52: Clean thermistor probe 12.
- Page 57 and 58:
Fig. 53: Clean thermistor probe Fig
- Page 59 and 60:
Calibrate device using calibration
- Page 61 and 62:
Fig. 63: Second calibration standar
- Page 63 and 64:
Configure screen saver Fig. 68: Con
- Page 65 and 66:
7.6 Power down device Fig. 72: Powe
- Page 67 and 68:
8.2 Notes regarding errors Fig. 75:
- Page 69 and 70:
Measurement procedure takes longer
- Page 71 and 72:
Device cannot be powered up Power s
- Page 73 and 74:
Fig. 77: Remove mounting screw Fig.
- Page 75 and 76:
Check free movement of initiation n
- Page 77 and 78:
Fig. 86: Move elevator down Fig. 87
- Page 79 and 80:
Fig. 93: Remove mounting plate 1 Mo
- Page 81 and 82:
Fig. 99: Elevator cover with correc
- Page 83 and 84:
8.4.3 Replace fine-wire fuses Fig.
- Page 85 and 86:
Fig. 108: Pull out printer Fig. 109
- Page 87 and 88:
Fig. 114: Pull out printer Fig. 115
- Page 89 and 90:
9.1 Service table OSMOMAT 3000 Serv
- Page 91 and 92:
Fig. 121: Remove mounting screws Fi
- Page 93 and 94:
Install device front panel Fig. 127
- Page 95 and 96:
Fig. 131: Lubricate elevator guide
- Page 97 and 98:
9.5 Check reproducibility of measur
- Page 99 and 100:
11 Specifications 11.1 Dimensions 1
- Page 101 and 102:
OSMOMAT 3000 Specifications Power c
- Page 103 and 104:
12 Index 2 2-point calibration ....
- Page 105 and 106:
T Temperature sensor Replace ......
- Page 107 and 108:
Fig. 138: "Safe Transport" menu Fig
- Page 109 and 110:
Classification of the IVD OSMOMAT 3
- Page 111:
Before Calling Gonotec Fig. 141: Co