User Guide

More documents

Recommendations

Info

OSMOMAT 3000 Design and function Consumables Fig. 7: Overview of consumables 24 Version 1.02 04/24/2013 NOTE! Risk of falsified measurement results! When using accessories and/or consumables made by manufacturers other than Gonotec GmbH, the reproducibility of the measurement results cannot be guaranteed. - Always use the accessories and consumables supplied by Gonotec GmbH. - Re-order consumables, in particular measuring vessels, from Gonotec GmbH (see page 2 for contact information). 1 Measuring vessels, 100 pc. 2 Calibration standard, 10 pc., 1ml each, concentration 300 mOsmol/kg 3 Printer paper, 1 roll
Accessories Fig. 8: Overview of accessories 1 Power cord 2 RS-232 cable 3 USB cable for printer connection (slave) 4 Adjustment tool 5 2 fine-wire fuses, 1 A 6 Ampoule opener OSMOMAT 3000 Design and function 7 Blow-out device for removing condensate (Pasteur pipette) Version 1.02 04/24/2013 25
Page 1 and 2: 2/12/2013 User Guide OSMOMAT 3000 V
Page 3 and 4: OSMOMAT 3000 Overview of the OSMOMA
Page 5 and 6: Table of Contents OSMOMAT 3000 Over
Page 7 and 8: OSMOMAT 3000 Overview of the OSMOMA
Page 9 and 10: Device, rear Fig. 2: Device overvie
Page 11 and 12: Accessories Fig. 4: Overview of acc
Page 13 and 14: Special safety notices Safety notic
Page 15 and 16: 2.3.2 Risk of infection Risk of inf
Page 17 and 18: 2.3.5 Reproducibility of the measur
Page 19 and 20: Inventory OSMOMAT 3000 Safety The o
Page 21 and 22: 2.6 Personal safety gear OSMOMAT 30
Page 23: Device, rear Fig. 6: Device overvie
Page 27 and 28: 3.3 Measurement equipment Fig. 9: O
Page 29 and 30: Thermistor probe Fig. 11: Thermisto
Page 31 and 32: Enter values Fig. 13: Enter values
Page 33 and 34: 3.6 Connections and interfaces Fig.
Page 35 and 36: 3.6.2 Transfer protocol Output form
Page 37 and 38: 4.1 Packaging About the packaging H
Page 39 and 40: 4.2 Device storage 4.3 Unpack devic
Page 41 and 42: 5.2 Install device Fig. 21: Fan out
Page 43 and 44: 6 Setup Check printer (Option D) Ch
Page 45 and 46: Select calibration standards Fig. 2
Page 47 and 48: 7.1 Power up device Fig. 31: Power
Page 49 and 50: Fig. 33: Start menu Fig. 34: Ice fo
Page 51 and 52: Fig. 40: Move elevator down Fig. 41
Page 53 and 54: Fig. 45: Ice formation Fig. 46: Cal
Page 55 and 56: Fig. 52: Clean thermistor probe 12.
Page 57 and 58: Fig. 53: Clean thermistor probe Fig
Page 59 and 60: Calibrate device using calibration
Page 61 and 62: Fig. 63: Second calibration standar
Page 63 and 64: Configure screen saver Fig. 68: Con
Page 65 and 66: 7.6 Power down device Fig. 72: Powe
Page 67 and 68: 8.2 Notes regarding errors Fig. 75:
Page 69 and 70: Measurement procedure takes longer
Page 71 and 72: Device cannot be powered up Power s
Page 73 and 74: Fig. 77: Remove mounting screw Fig.
Page 75 and 76:
Check free movement of initiation n
Page 77 and 78:
Fig. 86: Move elevator down Fig. 87
Page 79 and 80:
Fig. 93: Remove mounting plate 1 Mo
Page 81 and 82:
Fig. 99: Elevator cover with correc
Page 83 and 84:
8.4.3 Replace fine-wire fuses Fig.
Page 85 and 86:
Fig. 108: Pull out printer Fig. 109
Page 87 and 88:
Fig. 114: Pull out printer Fig. 115
Page 89 and 90:
9.1 Service table OSMOMAT 3000 Serv
Page 91 and 92:
Fig. 121: Remove mounting screws Fi
Page 93 and 94:
Install device front panel Fig. 127
Page 95 and 96:
Fig. 131: Lubricate elevator guide
Page 97 and 98:
9.5 Check reproducibility of measur
Page 99 and 100:
11 Specifications 11.1 Dimensions 1
Page 101 and 102:
OSMOMAT 3000 Specifications Power c
Page 103 and 104:
12 Index 2 2-point calibration ....
Page 105 and 106:
T Temperature sensor Replace ......
Page 107 and 108:
Fig. 138: "Safe Transport" menu Fig
Page 109 and 110:
Classification of the IVD OSMOMAT 3
Page 111:
Before Calling Gonotec Fig. 141: Co
show all

User Guide

Create successful ePaper yourself

Delete template?

Save as template?