User Guide

More documents

Recommendations

Info

OSMOMAT 3000 Delivery, packaging, and storage Package orientation No disposal via municipal waste Package recycling Conformity In vitro diagnostic product Item number Batch ID Expiration date 38 Version 1.02 04/24/2013 The arrow tips of the symbol point to the top of the package. They must point up at all times to prevent damage to the contents. Indicates that disposal of the device via municipal waste is prohibited. Disposal of the decommissioned device should be via electronics and metal recycling. In addition, decommissioned devices can be returned to the manufacturer for disposal. Indicates that the packaging can be recycled. This product meets the requirements of EEC Directive 98/79 relating to in-vitro diagnostics. In-vitro diagnostic product. Item number Batch ID of the calibration standard Expiration date (month, year). Date until which the calibration standard fulfills its original function if stored properly.
4.2 Device storage 4.3 Unpack device OSMOMAT 3000 Delivery, packaging, and storage Store the device under the following conditions: Do not store outside. Store under dry and dust-free conditions. Do not expose to aggressive media. Protect from sunlight. Protect the thermistor probe using a measuring vessel. Avoid mechanical shock. Storage temperature: -10°C to 60°C. Relative humidity (non-condensing): 5-90%. If stored for more than 3 months, regularly inspect all parts and packaging for general integrity. 1. Carefully open cardboard box using a knife. 2. Remove device from packaging and place in a suitable location. 3. Keep packaging for possible later return. Version 1.02 04/24/2013 39
Page 1 and 2: 2/12/2013 User Guide OSMOMAT 3000 V
Page 3 and 4: OSMOMAT 3000 Overview of the OSMOMA
Page 5 and 6: Table of Contents OSMOMAT 3000 Over
Page 7 and 8: OSMOMAT 3000 Overview of the OSMOMA
Page 9 and 10: Device, rear Fig. 2: Device overvie
Page 11 and 12: Accessories Fig. 4: Overview of acc
Page 13 and 14: Special safety notices Safety notic
Page 15 and 16: 2.3.2 Risk of infection Risk of inf
Page 17 and 18: 2.3.5 Reproducibility of the measur
Page 19 and 20: Inventory OSMOMAT 3000 Safety The o
Page 21 and 22: 2.6 Personal safety gear OSMOMAT 30
Page 23 and 24: Device, rear Fig. 6: Device overvie
Page 25 and 26: Accessories Fig. 8: Overview of acc
Page 27 and 28: 3.3 Measurement equipment Fig. 9: O
Page 29 and 30: Thermistor probe Fig. 11: Thermisto
Page 31 and 32: Enter values Fig. 13: Enter values
Page 33 and 34: 3.6 Connections and interfaces Fig.
Page 35 and 36: 3.6.2 Transfer protocol Output form
Page 37: 4.1 Packaging About the packaging H
Page 41 and 42: 5.2 Install device Fig. 21: Fan out
Page 43 and 44: 6 Setup Check printer (Option D) Ch
Page 45 and 46: Select calibration standards Fig. 2
Page 47 and 48: 7.1 Power up device Fig. 31: Power
Page 49 and 50: Fig. 33: Start menu Fig. 34: Ice fo
Page 51 and 52: Fig. 40: Move elevator down Fig. 41
Page 53 and 54: Fig. 45: Ice formation Fig. 46: Cal
Page 55 and 56: Fig. 52: Clean thermistor probe 12.
Page 57 and 58: Fig. 53: Clean thermistor probe Fig
Page 59 and 60: Calibrate device using calibration
Page 61 and 62: Fig. 63: Second calibration standar
Page 63 and 64: Configure screen saver Fig. 68: Con
Page 65 and 66: 7.6 Power down device Fig. 72: Powe
Page 67 and 68: 8.2 Notes regarding errors Fig. 75:
Page 69 and 70: Measurement procedure takes longer
Page 71 and 72: Device cannot be powered up Power s
Page 73 and 74: Fig. 77: Remove mounting screw Fig.
Page 75 and 76: Check free movement of initiation n
Page 77 and 78: Fig. 86: Move elevator down Fig. 87
Page 79 and 80: Fig. 93: Remove mounting plate 1 Mo
Page 81 and 82: Fig. 99: Elevator cover with correc
Page 83 and 84: 8.4.3 Replace fine-wire fuses Fig.
Page 85 and 86: Fig. 108: Pull out printer Fig. 109
Page 87 and 88: Fig. 114: Pull out printer Fig. 115
Page 89 and 90:
9.1 Service table OSMOMAT 3000 Serv
Page 91 and 92:
Fig. 121: Remove mounting screws Fi
Page 93 and 94:
Install device front panel Fig. 127
Page 95 and 96:
Fig. 131: Lubricate elevator guide
Page 97 and 98:
9.5 Check reproducibility of measur
Page 99 and 100:
11 Specifications 11.1 Dimensions 1
Page 101 and 102:
OSMOMAT 3000 Specifications Power c
Page 103 and 104:
12 Index 2 2-point calibration ....
Page 105 and 106:
T Temperature sensor Replace ......
Page 107 and 108:
Fig. 138: "Safe Transport" menu Fig
Page 109 and 110:
Classification of the IVD OSMOMAT 3
Page 111:
Before Calling Gonotec Fig. 141: Co
show all

User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?