User Guide

More documents

Recommendations

Info

OSMOMAT 3000 Installation 5 Installation 5.1 Transport device inside lab Fig. 18: Position measuring vessel Fig. 19: Position transport safety device Fig. 20: Device with protective sleeve 40 Version 1.02 04/24/2013 Personnel: <strong>User</strong> Safety gear: Disposable lab gloves 1. Power down device using on/off switch on rear side and disconnect power plug. 2. Position a measuring vessel (fig. 18/1) on the thermistor probe. The measuring vessel is securely attached to the thermistor probe when it clicks into place. 3. Tilt transport safety device for thermistor probe and carefully slide behind the thermistor probe (fig. 19). 4. Pull protective sleeve (fig. 20/1) included with the delivery over device. 5. Lift up device (6.5kg) and carry to installation site.
5.2 Install device Fig. 21: Fan outlet (1) Fig. 22: Remove protective sleeve Personnel: <strong>User</strong> Safety gear: Disposable lab gloves 1. NOTE! Risk of property damage! Only install device indoors. Install device at installation site. NOTE! Risk of incorrect measurements OSMOMAT 3000 Installation Select site based on the following criteria: - free of vibrations - no direct heat exposure (sun, electric heater, etc.) - no strong air flows - free of dust and dirt Keep fan outlet (fig. 21/1) clear. Keep fan outlet openings underneath device clear. 2. Remove protective sleeve from device (fig. 22/1). Version 1.02 04/24/2013 41
Page 1 and 2: 2/12/2013 User Guide OSMOMAT 3000 V
Page 3 and 4: OSMOMAT 3000 Overview of the OSMOMA
Page 5 and 6: Table of Contents OSMOMAT 3000 Over
Page 7 and 8: OSMOMAT 3000 Overview of the OSMOMA
Page 9 and 10: Device, rear Fig. 2: Device overvie
Page 11 and 12: Accessories Fig. 4: Overview of acc
Page 13 and 14: Special safety notices Safety notic
Page 15 and 16: 2.3.2 Risk of infection Risk of inf
Page 17 and 18: 2.3.5 Reproducibility of the measur
Page 19 and 20: Inventory OSMOMAT 3000 Safety The o
Page 21 and 22: 2.6 Personal safety gear OSMOMAT 30
Page 23 and 24: Device, rear Fig. 6: Device overvie
Page 25 and 26: Accessories Fig. 8: Overview of acc
Page 27 and 28: 3.3 Measurement equipment Fig. 9: O
Page 29 and 30: Thermistor probe Fig. 11: Thermisto
Page 31 and 32: Enter values Fig. 13: Enter values
Page 33 and 34: 3.6 Connections and interfaces Fig.
Page 35 and 36: 3.6.2 Transfer protocol Output form
Page 37 and 38: 4.1 Packaging About the packaging H
Page 39: 4.2 Device storage 4.3 Unpack devic
Page 43 and 44: 6 Setup Check printer (Option D) Ch
Page 45 and 46: Select calibration standards Fig. 2
Page 47 and 48: 7.1 Power up device Fig. 31: Power
Page 49 and 50: Fig. 33: Start menu Fig. 34: Ice fo
Page 51 and 52: Fig. 40: Move elevator down Fig. 41
Page 53 and 54: Fig. 45: Ice formation Fig. 46: Cal
Page 55 and 56: Fig. 52: Clean thermistor probe 12.
Page 57 and 58: Fig. 53: Clean thermistor probe Fig
Page 59 and 60: Calibrate device using calibration
Page 61 and 62: Fig. 63: Second calibration standar
Page 63 and 64: Configure screen saver Fig. 68: Con
Page 65 and 66: 7.6 Power down device Fig. 72: Powe
Page 67 and 68: 8.2 Notes regarding errors Fig. 75:
Page 69 and 70: Measurement procedure takes longer
Page 71 and 72: Device cannot be powered up Power s
Page 73 and 74: Fig. 77: Remove mounting screw Fig.
Page 75 and 76: Check free movement of initiation n
Page 77 and 78: Fig. 86: Move elevator down Fig. 87
Page 79 and 80: Fig. 93: Remove mounting plate 1 Mo
Page 81 and 82: Fig. 99: Elevator cover with correc
Page 83 and 84: 8.4.3 Replace fine-wire fuses Fig.
Page 85 and 86: Fig. 108: Pull out printer Fig. 109
Page 87 and 88: Fig. 114: Pull out printer Fig. 115
Page 89 and 90: 9.1 Service table OSMOMAT 3000 Serv
Page 91 and 92:
Fig. 121: Remove mounting screws Fi
Page 93 and 94:
Install device front panel Fig. 127
Page 95 and 96:
Fig. 131: Lubricate elevator guide
Page 97 and 98:
9.5 Check reproducibility of measur
Page 99 and 100:
11 Specifications 11.1 Dimensions 1
Page 101 and 102:
OSMOMAT 3000 Specifications Power c
Page 103 and 104:
12 Index 2 2-point calibration ....
Page 105 and 106:
T Temperature sensor Replace ......
Page 107 and 108:
Fig. 138: "Safe Transport" menu Fig
Page 109 and 110:
Classification of the IVD OSMOMAT 3
Page 111:
Before Calling Gonotec Fig. 141: Co
show all

User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?