3 - Wacker Neuson Group

More documents

Recommendations

Info

5 PD SERIES PUMPS PT / PG / PD REPAIR Notes: 5-22
Use Of Threadlockers and Sealants SEALANTS Threadlocking adhesives and sealants are specified throughout this manual and should be used where indicated. Threadlocking compounds normally break down at temperatures above 350° F (175° C). If a screw or bolt is hard to remove, heat it using a small propane torch to break down sealant. When applying sealants, follow instructions on container. The sealants listed below are recommended for use on WACKER equipment. TYPE ( ) = Europe COLOR USAGE PART NO. - SIZE Loctite 222 Purple Low strength, for locking threads smaller than 1/4" (6 mm). 73287 - 10 ml Hernon 420 Hand tool removable. Omnifit 1150 (50M) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) Loctite 243 Blue Medium strength, for locking threads larger than 1/4" (6 mm). 29311 - .5 ml Hernon 423 Hand tool removable. 17380 - 50 ml Omnifit 1350 (100M) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) Loctite 271 / 277 Red High strength, for all threads up to 1" (25 mm). 29312 - .5 ml Hernon 427 Heat parts before disassembly. 26685 - 10 ml Omnifit 1550 (220M) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) 73285 - 50 ml Loctite 290 Green Medium to high strength, for locking preassembled threads 28824 - .5 ml Hernon 431 and for sealing weld porosity (wicking). 25316 - 10 ml Omnifit 1710 (230LL) Gaps up to 0.005" (0.13 mm) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) Loctite 609 Green Medium strength retaining compound for slip or press fit 29314 - .5 ml Hernon 822 of shafts, bearings, gears, pulleys, etc. Omnifit 1730 (230L) Gaps up to 0.005" (0.13 mm) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) Loctite 545 Brown Hydraulic sealant 79356 - 50 ml Hernon 947 Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) Omnifit 1150 (50M) Loctite 592 White Pipe sealant with Teflon for moderate pressures. 26695 - 6 ml Hernon 920 Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) 73289 - 50 ml Omnifit 790 Loctite 515 Purple Form-in-place gasket for flexible joints. 70735 - 50 ml Hernon 910 Fills gaps up to 0.05" (1.3 mm) Omnifit 10 Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) Loctite 496 Clear Instant adhesive for bonding rubber, metal and plastics; Hernon 110 general purpose. 52676 - 1 oz. Omnifit Sicomet 7000 For gaps up to 0.006" (0.15 mm) Read caution instructions before using. Temp. range, -65 to 180 degrees F (-54 to 82 degrees C) Loctite Primer T Aerosol Fast curing primer for threadlocking, retaining and 2006124 - 6 oz. Hernon Primer 10 Spray sealing compounds. Must be used with stainless steel Omnifit VC Activator hardware. Recommended for use with gasket sealants.
Page 1:
www.wackergroup.com REPAIR MANUAL 0
Page 4 and 5:
FOREWORD PT / PG / PD REPAIR Namepl
Page 6 and 7:
FOREWORD PT / PG / PD REPAIR Item N
Page 8 and 9:
1 GENERAL PT / PG / PD REPAIR 1.1 S
Page 10 and 11:
1 GENERAL PT / PG / PD REPAIR 1.7 O
Page 12 and 13:
1 GENERAL PT / PG / PD REPAIR 1.10
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
2 OPERATION PT / PG / PD REPAIR 2.1
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
3 PT SERIES PUMPS PT / PG / PD REPA
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61: 3 PT SERIES PUMPS PT / PG / PD REPA
Page 72 and 73: 4 PG SERIES PUMPS PT / PG / PD REPA
Page 90 and 91: 5 PD SERIES PUMPS PT / PG / PD REPA
Page 112: TORQUE VALUES Metric Fasteners (DIN
show all

3 - Wacker Neuson Group

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?