20111104_CN.12_complete_UK_LOW.pdf

MIXO
180
MIXO modular units 1 or 4 poles + shield (each connector) 10A - 50V
the modular inserts must be installed in suitable
frames which in turn are installed in traditional
housings or COB panel support
frames for modular units ............... page: 195
- characteristics according to EN 61984:
10A 50V 0,8kV 3
- UL, CSA, CCC (no CX 01 B), GOST certified
- rated voltage according to UL/CSA: 50V
- insulation resistance: ≥ 10 GΩ
- ambient temperature limit:
-40 °C ... +70 °C (CX 01 B and CX 04 B)
- are made of self-extinguishing thermoplastic resin UL 94 V0
- mechanical life: ≥ 500 cycles
- contact resistance: ≤ 3 mΩ (no CX 02 B)
- coaxial connector CX 01 B cables with a typical
impedance of 75 Ω (atténuation see page 501)
- CX 04 B multiaxial connector for STP cables with 2 pairs and
terminations compliant with EN 50173-1 Cat. 5 (100 MHz),
compatible with 4-wire field bus protocols
- extraction tool for BUS shielded connectors from
MIXO BUS insert part No. CX BES see page 440
description part No. part No. part No.
seat for two shielded connectors
- female insert, two seats for BUS connectors CX 02 BF
- male insert, two seats for BUS connectors CX 02 BM
shielded BUS multi axial connectors, 4 poles + shield
- female insert, four contact seats + shield CX 04 BF
- male insert, four contact seats + shield CX 04 BM
shielded BUS coaxial connectors, 1 pole + shield
- female insert, one contact seats + shield CX 01 BF
- male insert, one contact seats + shield CX 01 BM
metal adaptor (optional) CR GND
10A female crimp contacts
0.14-0.37 mm2 AWG 26-22 CDFA 0.3 CDFD 0.3
0.5 mm2 AWG 20 CDFA 0.5 CDFD 0.5
0.75 mm2 AWG 18 CDFA 0.7 CDFD 0.7
1 mm2 AWG 18 CDFA 1.0 CDFD 1.0
1.5 mm2 AWG 16 CDFA 1.5 CDFD 1.5
2.5 mm2 AWG 14 CDFA 2.5 CDFD 2.5
10A male crimp contacts
0.14-0.37 mm 2 AWG 26-22 CDMA 0.3 CDMD 0.3
0.5 mm 2 AWG 20 CDMA 0.5 CDMD 0.5
0.75 mm 2 AWG 18 CDMA 0.7 CDMD 0.7
1 mm 2 AWG 18 CDMA 1.0 CDMD 1.0
1.5 mm 2 AWG 16 CDMA 1.5 CDMD 1.5
2.5 mm 2 AWG 14 CDMA 2.5 CDMD 2.5
Note:
The shielded connectors have their shield insulated
from the enclosure’s earthing point.
If you wish to earth-connect the shield, install on the
panel an anchorage for shielded cables CR..ST (see
page 425) or the CR GND metal adaptor..
Use of the CR GND metal adaptor
dimensions shown are not binding
and may be changed without notice
seat for shielded connectors shielded connectors
metal adaptor 10A crimp contacts, silver or gold plated
dimensions in mm
CX 02 BF, CX 02 BM CX 04 BF, CX 04 BM
34 29.4
contacts side (front view)
side with reference arrow ▲
F
- footprint 2 modules
CR GND
4.6
19
M
34
34
23
M
F
6÷9.5 3÷6
2 cable clamps included
in the package
CX 01 BF, CX 01 BM
6÷9.5 3÷6
2 cable clamps included
in the package
silver plated
gold plated
46.5 46
Ø 15.5 Ø 15.5
46,5 46
Ø 15.5 Ø 15.5
- conductors stripping length see page 178
- crimp contacts dimensions (CDF and CDM) see page 178
- for contact crimping, see the crimp tool section (10A contacts,
CDF and CDM series) on pages 466, 470, 480, 482, 484,
486