technical manual operator instructions

More documents

Recommendations

Info

2.12 INSTALLATION OF HOOD (CONT). d. Tighten ball lock on draw string until hood is securely attached to facepiece. Secure excess string. e. Remove facepiece and reverse hood over front of facepiece. Check that hood is fastened under lip of second skin (3). f. Stow mask in carrier (para 2.9). 2-61
2.13 WEAR AND LOCATION OF THE CANISTER. 2.13.1 Face Mounted. The C2 canister can be mounted directly to the facepiece. After removing the hose assembly from the facepiece, the canister is inserted into the side port and handtightened by turning clockwise. 2.13.2 Left-handed firers. During the initial fitting, the maintenance technician will change the canister position on the facepiece to allow for left-handed firing. WARNING Do not place canister where air intake is blocked. 2.13.3 Hose Mounted. Attach clip to clothing or survival vest in a place that will not block airflow into canister. The canister location should not interfere with mission performance. 2-62
Page 1 and 2:
TM 3-4240-341-10 TECHNICAL MANUAL O
Page 3 and 4:
WARNING SUMMARY This publication de
Page 5 and 6:
WARNING SUMMARY (CONT) o You must c
Page 7 and 8:
EXPLANATION OF SINGLE HAZARD SYMBOL
Page 9 and 10:
HEALTH/ENVIRONMENTAL HAZARD Filter
Page 11 and 12:
TABLE OF CONTENTS (CONT) APPENDIX A
Page 13 and 14:
Fig 1. Mask, Chemical-Biological: M
Page 15 and 16:
SECTION I. GENERAL INFORMATION (CON
Page 17 and 18:
SECTION I. GENERAL INFORMATION (CON
Page 19 and 20:
SECTION II. EQUIPMENT DESCRIPTION A
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
SECTION III. THEORY OF OPERATION (C
Page 29 and 30:
SECTION III. THEORY OF OPERATION (C
Page 31 and 32:
2.1.1 General (CONT). a. Perform PM
Page 33 and 34:
2.1.2 PMCS Procedures (CONT). f. Th
Page 35 and 36:
Table 2-1. PREVENTIVE MAINTENANCE C
Page 37 and 38:
Table 2-1. PREVENTIVE MAINTENANCE C
Page 39 and 40: Table 2-1. PREVENTIVE MAINTENANCE C
Page 67 and 68: 2.2 MANDATORY REPLACEMENT PARTS. Th
Page 69 and 70: 2.4 DONNING YOUR MASK (CONT). c. Pu
Page 71 and 72: 2.4 DONNING YOUR MASK (CONT). f. Bl
Page 73 and 74: 2.5 FIT CRITERIA. a. Verify the fit
Page 75 and 76: 2.6 PUTTING YOUR MASK ON IN COLD WE
Page 77 and 78: 2.7.1 CONNECTING THE DRINKING SYSTE
Page 79 and 80: 2.7.1 CONNECTING THE DRINKING SYSTE
Page 81 and 82: 2.8 REMOVING YOUR MASK. a. Disconne
Page 83 and 84: 2.9 STOWING YOUR MASK AND ADDITIONA
Page 85 and 86: 2.9 STOWING YOUR MASK AND ADDITIONA
Page 87 and 88: 2.10 WEARING YOUR MASK CARRIER (CON
Page 89: 2.12 INSTALLATION OF HOOD. a. Remov
Page 93 and 94: No lubrication is required for the
Page 95 and 96: 3.2 CHECKING YOUR MASK FOR LEAKS (C
Page 97 and 98: 3.4 CLEANING (CONT). c. Soak brush
Page 99 and 100: 3.4 CLEANING (CONT). m. Clean outsi
Page 101 and 102: APPENDIX A REFERENCES A-1. SCOPE. T
Page 103 and 104: APPENDIX B COMPONENTS OF END ITEM A
Page 105 and 106: B-3. EXPLANATIONS OF COLUMNS (CONT)
Page 107 and 108: APPENDIX C ADDITIONAL AUTHORIZATION
Page 109 and 110: SECTION II. ADDITIONAL AUTHORIZATIO
Page 111 and 112: D-2. EXPLANATION OF COLUMNS (CONT).
Page 114: DID WE GOOF? DO YOU KNOW A BETTER W
show all

technical manual operator instructions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?