Tender Specification for Supply, Erection, Testing and ... - IDCO

More documents

Recommendations

Info

The codes, regulation as detailed below shall be followed in this contract :- 1. Safety code for Air-conditioning (revised) amendment 1 IS 659 : 1964 (reaffirmed 1991) 2. Safety code foe Mechanical Refrigeration IS 660 : 1963 (reaffirmed 1991) 3. Testing of Refrigeration Compressors IS 5111 : 1993 4. Air-cooled Heat Exchangers (amendment 1) IS 10470 : 1983 (reaffirmed 1991) 5. Packaged Air-conditioner (amendment 1991) IS 8148 : 1976 (reaffirmed 1991) 6. Hermetic Compressors IS 10617 : Part I, II & III 1983 (reaffirmed 1991) 7. Suppliers Data Sheet for clean air equipment (laminar flow) IS 12357 : 1998 8. Thermostats for use in refrigeration etc. IS 11338 : 1965 (reaffirmed 1991) 9. Code of practice for design and construction of flue chimneys IS 11338 : 1965 (reaffirmed 1991) 10. Metal Duct Work IS 655 : 1963 (reaffirmed 1991) 11. Steel for general structural purpose IS 2062 : 1992 12. Piping Work IS 1239 Part I & II 1990 / 1992 IS & BS : 3601 13. Welding IS : 3589 14. Refrigeration As per ASHRAE / ISI Air-conditioning and Refrigeration Air-conditioning institute Standards. 15. Hot Dip Zinc Coated Steel Tubes IS 4736 : 1968 16. Gate Valves for Water lines IS 778 : 1980 17. Copper Alloy Gate Globe Check Valve for water lines IS 778 : 1980 18. Butterfly Valve IS 13095 : 1991 19. Steel Pipe flanges IS : 6392 20. Gaskets IS 638 : 1979 (reaffirmed 1993) 21. Mild steel tubes and fittings IS 1239 Part I & II 22. Dual plate Check Valve for Water Lines AP : 194 23. Colour code for the identification of pipe lines IS 2379 : 1963 24. Specific requirements for the direct switching of the individual motors. 25. PVC insulated (HD) Electric Cables for working voltage up Including 1100 Volts. IS 4064 ( Part II) 1978 IS : 1554 ( Part I) 26. HRC Cartridge fuse links upto 650 Volts. IS 2208 : 1976
27. Starter IS 8554 ( Part I) 1979 28. Inspection and testing of installation IS 732 ( Part III) 1979 29. Galvanized steel wire for fencing IS 277 : 1977 30. Three phase induction motors IS : 325 31. PVC insulated (heavy duty) cables for working voltage up to 1.1. KV and up to 11 KV Grade respectively. IS 1554 : 1981 Part I & II 32. Code for practice for electrical wiring installations. IS 732 : 1989 33. Code for practice for earthing IS 3043 : 1966 34. Horizontal centrifugal pumps IS : 1620 35. Centrifugal fans (1 st . Division) IS 894 : 1987 (reaffirmed 1991) 36. Wrought aluminum and aluminum alloy sheet and strip for general engineering purposes. 37. Mild steel tubes, tubular and other wrought steel fittings. IS : 737 IS : 1239 38. Bourden tube pressure and vacuum gauges. IS : 3624 39. Glossary of terms used in refrigeration and airconditioning. 40. Code for practice for standard for selection of standard worm and helical gears. IS : 3615 IS : 7403 41. Three phase induction motors. IS : 325 42. Specification for single phase small A/C and universal motors IS : 996 43. Specifications for flame proof motors IS : 2148 44. Circuit breaker A.C IS 2516 : 1980 Part I & II 45. Contactors for A.C for voltage upto 1100 V. IS 2959 : 1975 46. Low voltage switch gear and control gear assemblies. 47. Code of practice for selection of starters for AC induction motors IS 8623 : 1993 Part I & II IS 3914 48. Specification for cables glands IS 4821 49. Code for selection, installation and maintenance of switch gear and control gear. IS 10118 : 1982 Part I to IV 50. Conduits for electrical installations IS 9537 : 1981 Part I to IV 51. Permissible limits of noise level for rotating electrical machines. IS 12065 : 1987
Page 1 and 2: ISO 9001 & 14001 CORPORATION Tender
Page 3 and 4: ORISSA INDUSTRIAL INFRASTRUCTURE DE
Page 5 and 6: COMMERCIAL TERMS & CONDITIONS The B
Page 7 and 8: GUIDELINES ON BANK GUARANTEE The fo
Page 9 and 10: We, the said Bank, lastly undertake
Page 11 and 12: DEVIATION SHEET : PART - B If the p
Page 13 and 14: INSTRUCTION FOR THE TENDERER Genera
Page 15 and 16: GENERAL TERMS AND CONDITIONS OF CON
Page 17 and 18: In case the tenderer wish to deviat
Page 19 and 20: Negligence: If the contractor negle
Page 21 and 22: i. To have any part thereof complet
Page 23 and 24: Regulation of Local Authorities and
Page 25 and 26: Contract Labour Regulation and Abol
Page 27 and 28: However, the contractor may rectify
Page 29 and 30: INSTRUCTION / MAINTENANCE MANUAL: T
Page 31 and 32: WEEKLY PROGRESS REPORT: A weekly pr
Page 33: STANDARD SPECIFICATION SCOPE OF WOR
Page 37 and 38: SCROLL AIRCOOLED CHILLERS: The indi
Page 39 and 40: PUMP SETS: This section deals with
Page 41 and 42: COOLING COILS: The cooling coil sha
Page 43 and 44: a) RESIN BONDED FIBRE GLASS WOOL: T
Page 45 and 46: INSULATION OF PIPES: The chilled wa
Page 47 and 48: A) THE SUPPLY AND RETURN AIR GRILLS
Page 49 and 50: ) Proportionating Thermostat for AH
Page 51 and 52: Appropriate knock-out holes of prop
Page 53 and 54: DRAWINGS: Necessary drawings of all
Page 55 and 56: STANDARD SPECIFICATION ON PIPING WO
Page 57 and 58: LAYOUT AND SIZING OF PIPE LINES: Th
Page 59 and 60: e) Damper actuator shall be such th
Page 61 and 62: Sl. No. 1 Air-conditioned Areas on
Page 63 and 64: 24. Power Cable - ICC / CCI / Glost
Page 65 and 66: Sl. No. Floor and Area Name Area Li
Page 67 and 68: The capacity / rating of various eq
Page 69 and 70: TECHNICAL DATA (TO BE FILLED BY THE
Page 71 and 72: OVERALL SIZE OF WATER CHILLING MACH
Page 73 and 74: PIPE INSULATION: a) Manufactures Na
Page 75 and 76: CHILLED WATER PUMP: a) Flow rate LP
Page 77 and 78: D.6 Each push-button shall have min
Page 79 and 80: K. PAINTING: K.1 All surfaces will
Page 81 and 82: 18. Before delivery, the distributi
Page 83 and 84: BOQ FOR HV AC WORKS OF MCA BUILDING
Page 85 and 86:
Sl. No. Description Unit Quantity R
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93:
show all

Tender Specification for Supply, Erection, Testing and ... - IDCO

Create successful ePaper yourself

Delete template?

Save as template?