User Manual - Visionary Forces

More documents

Recommendations

Info

ENABLE / DISABLE SENSOR TEST PATTERN When selected enables / disables the sensor test pattern (White Screen). To turn on, select ENABLE SENSOR TEST PATTERN. To turn off, select DISABLE SENSOR TEST PATTERN. 955-0002_v3.2, Rev-A1 COPYRIGHT © 2012 RED Digital Cinema 139
TOUCHSCREEN When selected allows you to perform a touchscreen self-test. When the touchscreen self-test is on, you can verify all areas of the touch screen respond to touch. Simply touch each box using your finger. The touchscreen responds to the touch and the Green box turns Blue. To exit the Touchscreen Self-Test: Place your finger on the touchscreen and hold it there until the main screen appears. Press the Enter or Menu button on the Side Handle or REDMOTE. RESTORE SYSTEM Restore System permits ALL camera configuration and setup data to be reset to factory default values. 140 COPYRIGHT © 2012 RED Digital Cinema 955-0002_v3.2, Rev-A1
Page 2 and 3:
TABLE OF CONTENTS TABLE OF CONTENTS
Page 4 and 5:
DISCLAIMER RED ® has made every ef
Page 6 and 7:
AUSTRALIA AND NEW ZEALAND STATEMENT
Page 8 and 9:
BEFORE YOU START Congratulations on
Page 10 and 11:
CAUTION: The power cord plug for th
Page 12 and 13:
This recording technique permits RG
Page 14 and 15:
LINE LEVEL ANALOG INPUTS The record
Page 16 and 17:
REDMOTE ® REDMOTE is a camera cont
Page 18 and 19:
Where: A = camera A, 001 = reel 001
Page 20 and 21:
CAMERA OPERATIONAL CONTROLS This se
Page 22 and 23:
SSD Slot: Slot for REDMAG 1.8” SS
Page 24 and 25:
FRONT A A Stills / Movie Slider Sid
Page 26 and 27:
Navigation Group: Allows navigation
Page 28 and 29:
To remove the side handle: 1. Power
Page 30 and 31:
DUAL BATTERY MODULE The DUAL BATT
Page 32 and 33:
5. Tighten the screws again in a cr
Page 34 and 35:
2. Rotate module down flush with th
Page 36 and 37:
Default settings for User Function
Page 38 and 39:
TOUCHSCREEN LCD Red offers a five i
Page 40 and 41:
QUAD BATTERY MODULE The optional QU
Page 42 and 43:
AC POWER ADAPTOR - (DSMC) AC POWER
Page 44 and 45:
POWER UP Locate the camera’s Powe
Page 46 and 47:
GRAPHICAL USER INTERFACE AND NAVIGA
Page 48 and 49:
The GUI is broken down into the fol
Page 50 and 51:
GEN GEN Gray - No genlock signal
Page 52 and 53:
SIDE HANDLE As you navigate and adj
Page 54 and 55:
USING TOUCHSCREEN LCD If operating
Page 56 and 57:
POWER DOWN NOTE: Camera will automa
Page 58 and 59:
FIRST TIME USE - SETTING UP YOUR RE
Page 60 and 61:
RED BRICK Attach to the camera usin
Page 62 and 63:
PERFORM A BLACK SHADING CALIBRATION
Page 64 and 65:
CAMERA ID (SLATE) If operating on a
Page 66 and 67:
MENU CONTROLS Displayed in the Uppe
Page 68 and 69:
MAIN MENU Available options under t
Page 70 and 71:
ISO (SENSITIVITY) Adjusts the camer
Page 72 and 73:
FOCUS Provides the ability to enter
Page 74 and 75:
INTEGRATION TIME Provides the abili
Page 76 and 77:
ADVANCED SETTINGS When selected, al
Page 78 and 79:
RESOLUTION Allows adjustment of res
Page 80 and 81:
HDR ON / OFF By default, HDRx is OF
Page 82 and 83:
Performance of Auto Focus may be re
Page 84 and 85:
DSMC CANON MOUNT ELECTRONICALLY SUP
Page 86 and 87:
SPOT Provides a small, square targe
Page 88 and 89:
LENS INFORMATION DISPLAY RED DSMC T
Page 90 and 91: Select Create and enter a name for
Page 92 and 93: COPY PRESETS FROM CAMERA TO SSD U
Page 94 and 95: MEDIA MENU The Media Menu is used t
Page 96 and 97: UTILITIES Options are SECURE FORMAT
Page 98 and 99: EXPOSURE This will show areas of un
Page 100 and 101: ORANGE Super White (IRE 105-107) RE
Page 102 and 103: RAW RAW displays the image without
Page 104 and 105: Low IRE Change the desired setting
Page 106 and 107: MODES Available GUI display mode ad
Page 108 and 109: SIZE Available options are Off, Ful
Page 110 and 111: CONTRAST Adjusts the overall contra
Page 112 and 113: COLOR/GAMMA The COLOR/GAMMA sub-men
Page 114 and 115: TIME CODE DISPLAY Allows you to cho
Page 116 and 117: AUDIO/VIDEO Menu adjusts AUDIO INPU
Page 118 and 119: AUDIO OUTPUT Allows adjustment of a
Page 120 and 121: Limiter Enables signal limiter circ
Page 122 and 123: TEST SIGNALS Permits the video moni
Page 124 and 125: OPTIONS Select the desired option
Page 126 and 127: DATE / TIME This menu allows the us
Page 128 and 129: NETWORK If the Gigabit Ethernet por
Page 130 and 131: GPIO GPIO selects the GPIO preferen
Page 132 and 133: SYNC MODE Allows the shutter timing
Page 134 and 135: INDICATORS Beep Speaker Available o
Page 136 and 137: CALIBRATION Sensor calibration is a
Page 138 and 139: BLACK SHADING PROCEDURE The calibra
Page 142 and 143: When selected, you will be asked to
Page 144 and 145: PLAYBACK Playback allows you to vie
Page 146 and 147: PRESETS Allows you to apply presets
Page 148 and 149: SETTINGS Available options are DISP
Page 150 and 151: CLIP PLAYBACK STATUS BAR Displays t
Page 152 and 153: IN / OUT POINT MARKER Allows you to
Page 154 and 155: SHUTDOWN Power OFF controls are int
Page 156 and 157: APPENDIX B: MANAGING DIGITAL MEDIA
Page 158 and 159: MEDIA CAPACITY REMAINING STATUS The
Page 160 and 161: ERASING MEDIA NOTE: If the media wa
Page 162 and 163: MIC-1, MIC-2 (MICROPHONE AUDIO) Two
Page 164 and 165: HD-SDI A standard 75 Ohm BNC connec
Page 166 and 167: The Video Genlock input may be used
Page 168 and 169: CTRL (RS232 CONTROL) A 4-pin LEMO c
Page 170 and 171: DC IN (POWER INPUT) The 6-pin LEMO
Page 172 and 173: SIDE SSD MODULE REAR B FRONT A A B
Page 174 and 175: APPENDIX D: DEFAULT KEY FUNCTIONS C
Page 176 and 177: APPENDIX E: REDMOTE OPERATION CONTR
Page 178 and 179: C A B REDMOTE Navigation Group A Sc
Page 180 and 181: Note: For illustration only: rear s
Page 182 and 183: RECORDING To record, press the Red
Page 184 and 185: ADVANCED OPERATION: REDMOTE MENUS S
Page 186 and 187: Note: Once this procedure has occur
Page 188 and 189: OPERATING WITH MULTIPLE CAMERAS FRO
Page 190 and 191:
6. Select “Setup Slot” and pres
Page 192 and 193:
MAINTENANCE INTERNAL BATTERY CHARGE
Page 194 and 195:
UPGRADING REDMOTE FIRMWARE The REDM
Page 196 and 197:
7. Click “Connect”. When REDMOT
Page 198 and 199:
12. Once the File Transfer Status i
Page 200 and 201:
5. Select “I Agree” to the lice
Page 202 and 203:
10. The program will now install. A
Page 204 and 205:
9. The selected file is shown in th
Page 206 and 207:
16. Select “Disconnect” on the
Page 208 and 209:
SLAVE CAMERA Perform the following
Page 210 and 211:
Green BNC connector is for Tri-Leve
Page 212 and 213:
ISO 800 - False Color: Exposure Sel
Page 214 and 215:
ISO 800 - False Color: Exposure Sel
Page 216 and 217:
APPROPRIATE EXPOSURE ISO 800 - Moni
Page 218 and 219:
ISO 800 - False Color: Video Select
Page 220 and 221:
ISO 100 - No Exposure Adjustment In
Page 222 and 223:
REDCINE-X ® PRO REDCINE-X PRO is a
Page 224 and 225:
DO NOT USE any other solvents, chem
Page 226 and 227:
4. Power up the camera. 5. Power up
Page 228 and 229:
APPENDIX J: TROUBLESHOOTING NO MEDI
Page 230 and 231:
CAMERA BRAIN DIMENSIONS Front View
Page 232 and 233:
Top View Bottom View 955-0002_v3.2,
Page 234 and 235:
APPENDIX L: RESOLUTION CHART 955-00
Page 236 and 237:
MAIN MENU DEFAULT VALUES ARE DISPLA
Page 238 and 239:
SECONDARY MENUS PRESS MENU ICON (LC
Page 240:
SECONDARY MENUS PRESS MENU ICON (LC
show all

User Manual - Visionary Forces

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?