INSTRUCTION MANUAL

More documents

Recommendations

Info

$orionÂ® Eonâ¢ apochromatic ED refractors$

The NexStar comes completely pre-assembled and can be operational in a matter of minutes. The NexStar and its accessories are conveniently packaged in one reusable shipping carton that contains the following accessories: • 25mm Plossl Eyepiece – 1¼" • 1¼" Star Diagonal • Star Pointer Finderscope and Mounting Bracket • 1¼" Visual Back (attached to the optical tube) • Electronic Hand Control Assembling the NexStar Start by removing the telescope from its shipping carton and setting the round base on a flat table or surface. It is best to carry the telescope by holding it from the lower portion of the fork arm and from the bottom of the base. Remove all of the accessories from their individual boxes. Remember to save all of the containers so that they can be used to transport the telescope. Powering the NexStar The NexStar can be powered by eight user supplied AA batteries or with an optional AC adapter or cigarette lighter adapter. The battery compartment is located in the center of the telescope's base (see figure 3-1). To power the NexStar with batteries: 1. Slowly rotate the optical tube upwards so that you have easy access to the battery compartment. Battery Compartment 2. Remove the battery cover from the center of the base by gently lifting up on the round portion of the cover. 3. Insert the batteries into the battery compartment of the base. 4. Reattach the battery compartment door by gently pushing down on the cover until it snaps into place. 5. Turn on the power to the NexStar by flipping the switch, located at the bottom portion of the fork arm, to the "On" position. Figure 3-1: The NexStar can be powered with 8 AA batteries. 8
The Hand Control The hand control is located on the side of the fork arm and can be removed and used remotely or used while attached to the fork. The hand control attaches to the fork arm by resting on two posts, located on the bottom of the hand control cradle, and a clip inside the fork arm. To remove the hand control from the fork arm cradle, gently lift the hand control upwards and pull out. To return the hand control into the fork arm, lower the hand control into the cradle so that the opening in the back of the hand control slides over the clip inside the fork arm. NOTE Once the telescope is powered up, use the hand control to move the optical tube to the horizontal position, this will make it more convenient to attach the necessary accessories as well as remove the front lens cover. In case of a loss of power, the optical tube can be moved by hand. However, when powered on, the telescope should always be controlled via the hand control. The Star Diagonal The star diagonal diverts the light at a right angle from the light path of the telescope. For astronomical observing, this allows you to observe in positions that are more comfortable than if you were to look straight through. To attach the star diagonal: 1. Turn the thumbscrew on the visual back until its tip no longer extends into (i.e., obstructs) the inner diameter of the visual back. 2. Slide the chrome portion of the star diagonal into the visual back. 3. Tighten the thumbscrew on the visual back to hold the star diagonal in place. If you wish to change the orientation of the star diagonal, loosen the thumbscrew on the visual back until the star diagonal rotates freely. Rotate the diagonal to the desired position and tighten the thumbscrew. The Eyepiece The eyepiece, or ocular, is the optical element that magnifies the image focused by the telescope. The eyepiece fits into either the visual back directly or the star diagonal. To install the eyepiece: 1. Loosen the thumbscrew on the star diagonal so it does not obstruct the inner diameter of the eyepiece end of the diagonal. 2. Slide the chrome portion of the eyepiece into the star diagonal. 3. Tighten the thumbscrew to hold the eyepiece in place. StarPointer Finderscope Eyepiece To remove the eyepiece, loosen the thumbscrew on the star diagonal and slide the eyepiece out. Visual Back Eyepieces are commonly referred to by focal length and barrel diameter. The focal length of each eyepiece is printed on the eyepiece Figure 3-2 - The Visual Accessories barrel. The longer the focal length (i.e., the larger the number) the lower the eyepiece power or magnification; and the shorter the focal length (i.e., the smaller the number) the higher the magnification. Generally, you will use low-to-moderate power when viewing. For more information on how to determine power, see the section on “Calculating Magnification.” Barrel diameter is the diameter of the barrel that slides into the star diagonal or visual back. The NexStar uses eyepieces with a standard 1-1/4" barrel diameter. Star Diagonal 9
Page 1 and 2: ® INSTRUCTION MANUAL 1 NexStar 5i
Page 3 and 4: TELESCOPE BASICS...................
Page 5 and 6: 10 1 2 3 9 4 8 5 7 6 Figure 1-A - T
Page 7: 5 in 7 Direction Buttons Focus Knob
Page 11 and 12: 1. To turn on the Star Pointer, rot
Page 13 and 14: 5 1 2 4 3 Figure 4-1 The NexStar El
Page 15 and 16: 2. Press the STAR button on the han
Page 17 and 18: Your NexStar i-Series telescope is
Page 19 and 20: Alignment Procedures In order for t
Page 21 and 22: Helpful Hint 4. NexStar then asks y
Page 23 and 24: aligning your scope. For more infor
Page 25 and 26: Direction Buttons The NexStar has f
Page 27 and 28: To replace the contents of any of t
Page 29 and 30: Wedge Align - The NexStar has two e
Page 31 and 32: 1 2 APPENDIX C LONGITUDE LATITUDE d
Page 33 and 34: A telescope is an instrument that c
Page 35 and 36: distance of one thousand yards. The
Page 37 and 38: Motion of the Stars The daily motio
Page 39 and 40: Finding the North Celestial Pole In
Page 41 and 42: Observing the Sun Although overlook
Page 43 and 44: After looking at the night sky for
Page 45 and 46: eady for your next shot. Keep in mi
Page 47 and 48: Terrestrial Photography Your NexSta
Page 49 and 50: To verify collimation, view a star
Page 51 and 52: You will find that additional acces
Page 53 and 54: top or side of the telescope, makin
Page 55 and 56: APPENDIX A - TECHNICAL SPECIFICATIO
Page 57 and 58: Appendix B - Glossary of Terms A- A
Page 59 and 60:
Right Ascension: (RA) resolution. t
Page 61 and 62:
LONGITUDE LATITUDE degrees min degr
Page 63 and 64:
LONGITUDE LATITUDE degrees min degr
Page 65 and 66:
Appendix D - RS-232 Connection (for
Page 74 and 75:
CELESTRON ONE YEAR WARRANTY A. Cele
show all

INSTRUCTION MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?